EasyManuals Logo

Datalogic PowerScan PBT9500 User Manual

Datalogic PowerScan PBT9500
346 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #300 background imageLoading...
Page #300 background image
References
290
PowerScan™ PD9530/PBT9500/PM9500
PM9500-Only Features
Changing System Speed in Normal Mode
1. Link the PM9500 with a BC9xxx Base.
2. With the PM9500, read a Compatible Mode programming label on
pa
ge 238
to set low, intermediate, or high speed.
3. Place the PM9500 into the BC9xxx.
The Reader and Base will now be linked at
th
e new programmed speed.
This feature can also be programmed using
Datalogic Aladdin.
1. On the BC9xxx Base, change the Compatible mo
de parameter to low,
intermediate, or high speed through Aladdin.
2. Place an unlinked PM9500 onto the BC9xxx base.
The Reader and base will link with the new
programmed
speed.
Bluetooth-Only Features
Bluetooth Pin Code
This option specifies the 4-character or 16-character pin code to be used
for authentication of the Bluetooth
link. To set the pin code:
1.
Sc
an the
ENTE
R/EXIT PROGRAMMING MODE bar code to enter Program-
ming Mode, then enable
"Bluetooth Security Mode" on page 224.
2. Specify the desired pin code
length (4 or 16) by scanning the appropri-
ate bar code in
"Select PIN Code Length" on pa
ge 224.
3. Determine the desired characters. For example, D254 or
STOR12
345678135M.
4. Convert the characters to hexadecimal using the
ASCII Chart on the
inside
back cover of this manual.
5. Go to
page 224 and Scan the bar code: SET 4 CHAR PIN CODE or SET
16-CHAR PIN CODE.
6. Scan the appropriate alphanumeric characters from the keypad in
Appendix D, Keypad, representing the hexadecimal entries determined
in the steps above. You will hear a two-beep indication after the last
c
h
aracter.
If you make a mistake before the last character, scan the CANCEL bar code
to abort and not save the entry string. You can then start again at the
beginning.

Table of Contents

Other manuals for Datalogic PowerScan PBT9500

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Datalogic PowerScan PBT9500 and is the answer not in the manual?

Datalogic PowerScan PBT9500 Specifications

General IconGeneral
TypeHandheld bar code reader
Wavelength680 nm
Sensor typeLaser
Scanner type1D/2D
Tilt reading angle0 - 360 °
Pitch reading angle0 - 40 °
Light levels (direct sunlight)0 - 100000 lx
Linear (1D) barcodes supported-
2D (matrix & stacked) barcodes supportedAztec Code, Data Matrix, MaxiCode, Micro QR Code, QR Code
Battery life10 h
Charging time4 h
Battery capacity2150 mAh
Power source typeBattery
Number of reads per charge30000
Number of batteries supported1
Wireless range100 m
Operating frequency2400 - 2480 MHz
Standard interfacesUSB, RS-232
Connectivity technologyWired & Wireless
Storage temperature (T-T)-40 - 70 °C
Operating temperature (T-T)-20 - 50 °C
Operating relative humidity (H-H)0 - 95 %
BuzzerYes
CertificationIEC 62471 Class 1 LED
Product colorBlack, Yellow
Protection featuresShock resistant, Water resistant
International Protection (IP) codeIP65
Cables includedRS-232
Weight and Dimensions IconWeight and Dimensions
Depth74 mm
Width110 mm
Height212 mm
Weight380 g

Related product manuals