2 Introduction
© Travis Industries 4150126 100-01418
Overview
This manual details the DaVinci category 2
fireplace.
Listing Details
This appliance was listed by Intertek (Warnock
Hersey) to ANSI Z21.50b-2014 / CSA 2.22b-2014.
The listing label is chained to the appliance near
the glass frame. A copy is shown to the right.
Massachusetts Approval
This manual has been submitted to the
Massachusetts Board of State Examiners of
Plumbers and Gas Fitters
National Fireplace Institute
Dealer Information
Please record your dealer information here for
future reference:
Dealer Name: ____________________
Dealer Address: ____________________
Dealer E-Mail: ____________________
Dealer Phone #: ____________________
Report No. 100884872PRT-001
Control No. 4000515
Vented Gas Fireplace Heater
DaVinci L.P.
DaVinci N.G.
Tested to: ANSI Z21.50-2014/CSA 2.22-2014 Gas-Fired Domestic and Commercial Heating Equipment “Vented
Gas Fireplace”
This appliance must be installed in accordance with local codes, if any; if none, follow the National Fuel Gas
Code, ANSI Z223.1/NFPA 54, or Natural Gas and Propane Installation Codes, CSA B149.1.
This appliance must be installed in accordance with the Standard for Manufactured Homes, CAN/CSA Z240 MH
Series, or with the Manufactured Home Construction and Safety Standard, Title 24 CFR, Part 3280, or when such
a standard is not applicable, the Standard for Fire Safety Criteria for Manufactured Home Installations, Sites and
Communities, NFPA 501A
This vented gas fireplace heater is equipped at the factory for use with gas fuel marked above. No conversion is
allowed.
This appliance is only for use with the type of gas indicated on the rating plate and may be installed in an
aftermarket, permanently located, manufactured home (USA only) or mobile home, where not prohibited by local
codes. See owner’s manual for details. This appliance is not convertible for use with other gases, unless a
certified kit is used.
This vented gas fireplace heater is not for use with air filters.
Keep burner and control compartment clean. See installation and operating instructions accompanying
appliance.
This appliance must be properly connected to a venting system in accordance with the manufacturer’s
installation instructions. See owner’s manual for approved brands of venting.
WARNING: Improper installation, adjustment, alteration, service or maintenance can cause injury or property
damage. Refer to the owner’s information manual provided with this appliance. For assistance or additional
information consult a qualified installer, service agency or the gas supplier.
VENTED GAS FIREPLACE HEATER - NOT FOR USE WITH SOLID FUEL
Minimum Clearances to Combustibles
Fireplace to Adjacent Wall
Wood Floor Beneath Fireplace
Back to Enclosure
1” (26mm)
0” (0mm)
0” (0mm)
Top to Enclosure
Sides to Enclosure
Base of Fireplace to a Mantel
5.5” (140mm)
0” (0mm)
See Owner’s Manual
Electrical Rating: 120V., 60 Hz., Less than 7.0 Amps
DANGER! Risk of Electric Shock. Disconnect power before servicing unit.
Minimum Inlet Pressure (inches W.C.)
Maximum Inlet Pressure (inches W.C.)
Manifold Pressure on “HI” (inches W.C.)
L.P.
11”
13”
10”
N.G.
5.5”
7”
3.5”
This appliance is equipped for use only at altitudes 0-2,000 feet (0-610m) in the USA. In Canada, 0-4,500 feet (0-1370m).
For altitudes above 2,000 feet, the vent configuration, orifice, or combination of both may need to be changed.
See owner’s manual for information on making these changes.
Input Rate on “HI” (BTU/Hr)
Orifice Sizes - (DMS)
L.P.
#56
N.G.
#49
2015
2016
2014
Feb.
Mar.
Jan.
May
Jun.
Apr.
Aug.
Sep.
Jul.
Nov.
Dec.
Oct.
MANUFACTURE DATE:
WARNING: Failure to install this appliance per the manufacturer’s instructions or failure to use only parts
specifically approved with this appliance may result in property damage or personal injury.
12521 Harbour Reach Drive
Mukilteo, WA 98275
Manufactured by:
www.travisproducts.com
CAUTION:
Do not operate this appliance with glass removed, cracked or broken. Replacement of the panel(s) should be done
by a licensed or qualified service person.
XXXX
To Next Page
Loading...