DeLaval MPCII

To Next Page

To Previous Page

Operation

DeLaval milking point controller MPCII

94381001.pdf2006-07-20

application

page

active application program

application program

version

application

page

Not active application program

application program

version

90(94)

Main Page

Table of Contents3
Delaval Milking Point Controller MPCII9
- Product Data9
Mpcii/Alfadast13
- Installation13
  - MPCII Connections14
    - MPCII with Alfadast14
Mpcii/Herringbone17
- Installation17
Mpcii/In-Parlour Feeding27
- Installation27
  - MPCII Connections28
    - MPCII with Electrically Operated In-Parlour Feeding28
    - MPCII with Vacuum Operated In-Parlour Feeding29
Mpcii/Midiline31
- Installation31
  - MPCII Connections31
Mpcii/Rotary37
- Installation37
  - MPCII Connections37
Mpcii/Tandem43
- Installation43
  - MPCII Connections43
    - MPCII each Box44
    - MPCII Special45
Mpcii/Parallel47
- Installation47
Delaval Milking Point Controller MPCII57
- Operation57
- Forced Low to High Vacuum65
- Manual Control65
- Remind Codes66
- Milk Phase66
- Communication Interrupted66
Functions66
- F0 - Memory Lock66
- F1 - Go to Milking Mode66
- F2 - Go to Standby Mode67
- F3 - Milk Yield67
- F4 - Local Confirm67
- F5 - Confirm a Row67
- F6 - Cow Number/Milk Yield67
- F7 - Show Group Number68
- F8 - Deactivates Retraction68
- F9 - Open Memory68
- F11 - Transponder / Group Number68
- F13 - Calving Date Read/Write Function69
- F21 - Ration Data Read/Write Function69
- No Available Data70
- F22 - Consumed Feed Read Only70
- F30 - Milking Summary71
- F31 - Present Milking Read Only71
- F32 - Today's and Yesterday's Milk Yields Read/Write Function72
- F39 - Expected Milk Yield Read Only72
- F43 - Show Last Transponder Read Only73
- F45 - Breeding Status on MPCII73
- F62 - General Parameters74
- F63 - General Parameters76
Normal Milking78
- F62 - Options79
F63 - Limits, Timers, and Options80
F64 - High Vacuum Delay82
F71 - Go to Milking Mode82
F72 - Go to Standby Mode82
F75 - Local Mode83
F76 - Test Mode83
F78 - Configuration Check84
F79 - Show Mpcii's Address84
F82 - Local Cleaning Mode85
F83 - Deactivate Entrance Photocell85
F84 - Open/Close Main Gates86
F85 - no more Cows86
F86 - Exit Blocked86
F87 - Water Test87
F88 - Calibration88
F89 - Check Calibration88
F91 - Set Default Parameters88
F94 - Liner Data88
F95 - Reset Software89
F96 - Shows the Application Programs Information89
F97 - BOOT Version90
F98 - Application Version90
F100 - Cow Not Ready Milked90
F101 - Stop of Platform90
F371-F374 - Cow Status91
F371 - Do Not Milk Status93
F442 - Calibration Data93
F611 - Show Time94
F443 - Calibration Start94
F444 - Stop Dispensing94
F449 - Calibration Start One Side94
Stop Feeding94
F840 - Opens All Gates95
F901 - Milk Meter Offset95
New Feature on the MPCII95
Service99
Change of MPCII to a MPCII99
Troubleshooting101

Table of Contents