How to resolve a linear scale wiring error on Delta Servo Drives?
To resolve a linear scale wiring error on Delta Servo Drives, check all wiring connections of the linear scale and reconnect the wiring if necessary.
What to do if write parameter error occurs: read only on Delta Servo Drives?
If the parameter is read only, correct the PR command and parameter setting value.
How to resolve CANopen SDO receives buffer overflow in Delta ASDA-A2 Servo Drives?
To resolve CANopen SDO receives buffer overflow in Delta Servo Drives (receives more than two SDOs within 1 ms), use NMT: Reset node or 0x6040.Fault Reset.
What causes abnormal EEPROM in Delta ASDA-A2 Servo Drives?
If your Delta Servo Drives are showing an abnormal EEPROM: * It is in error when DSP accesses EEPROM: The fault occurs when applying to the power. It means one of the parameters is over the reasonable range. Please re-power on after adjusting. The fault occurs in normal operation. It means it is in error when writing the parameter. The alarm can be cleared by DI.ARST. * Abnormal hidden parameter: Please set the correct type of the drive. * Data in ROM is damaged: Please send the drive back to the distributors or contact with Delta.
What to do if EE-PROM invalid address range occurs on Delta ASDA-A2 Servo Drives?
If the amount of the data saved in EE-PROM has exceeded the space determined by the firmware, NMT Maser send “Reset node“ command to its slave or reset the fault by sending the control word (0x6040) through CAN communication (the value of CANopen object 0x6040 should be reset).
What to do if Delta ASDA-A2 show Encoder temperature exceeds the protective range?
If your Delta Servo Drives are showing that the encoder temperature exceeds the protective range, above 105?, improve heat dissipation or reduce the loading of operation.
How to resolve CANopen PDO is read-only and write-protected in Delta Servo Drives?
To resolve CANopen PDO is read-only and write-protected in Delta Servo Drives, when the specified object in the message is write- protected, use NMT: Reset node or 0x6040.Fault Reset.
What to do if sub-index error occurs when accessing CANopen object on Delta ASDA-A2?
If the specified Sub-index in the message does not exist, NMT Maser send “Reset node“ command to its slave or reset the fault by sending the control word (0x6040) through CAN communication (the value of CANopen object 0x6040 should be reset).
What to do if data type (size) error occurs when accessing CANopen object on Delta ASDA-A2 Servo Drives?
If the data length in the message does not match the specified object, NMT Maser send “Reset node“ command to its slave or reset the fault by sending the control word (0x6040) through CAN communication (the value of CANopen object 0x6040 should be reset).
What to do if data range error occurs when accessing CANopen object on Delta ASDA-A2?
If the data in the message has exceeded the data range of the specified object, NMT Maser send “Reset node“ command to its slave or reset the fault by sending the control word (0x6040) through CAN communication (the value of CANopen object 0x6040 should be reset).
General| Enclosure Rating | IP20 |
|---|---|
| Control Mode | Position, Speed, Torque |
| Communication Interface | RS-485, CANopen |
| Protection | Overcurrent, Overvoltage, Undervoltage, Overload, Overtemperature, Encoder error |
| Operating Temperature | 0°C to 55°C |
| Storage Temperature | -20°C to 65°C |
| Humidity | 20% to 90% RH (non-condensing) |
| Altitude | 1000m max |
| Cooling Method | Natural cooling or forced air cooling |
| Encoder Feedback | 20-bit incremental encoder (standard), 17-bit absolute encoder (optional) |
Pre-operation checks for product condition and functionality.
Nameplate information and detailed model code explanation for ASDA-A2 and ECMA series.
Matching specifications for servo drives and motors across different voltage series.
Identification and function of various parts of the servo drive.
Important notes on connections, voltage, and wiring.
Environmental conditions required for installing the servo drive and motor.
Guidelines for correct mounting and ventilation space.
Recommended circuit breakers and fuses for various series.
Recommendations for EMI filters and installation precautions.
Guidelines for selecting regenerative resistors.
Wiring information for 220V series servo drives.
How to connect external devices to the servo drive.
Detailed description of servo drive connectors and terminals.
Wiring methods for single-phase and three-phase power.
Specifications for motor power cables.
Specifications for encoder cable connectors.
Wiring information for 400V series servo drives.
How to connect external devices to 400V series drives.
Detailed description of 400V series drive connectors and terminals.
Wiring methods for 400V series servo drives.
Basic wiring diagrams for 220V and 400V series.
Details on connecting I/O signals to the CN1 connector.
Pinout and layout of the CN1 connector.
Explanation of signals for the CN1 connector.
Details on the CN2 connector for motor encoder connection.
Information on wiring the CN3 connector for communication.
Details on the CN4 serial connector for PC connection via USB.
Information about the CN5 connector for full-closed loop applications.
Details on the CN6 connector for CANopen communication.
Standard wiring examples for the 220V series.
Standard wiring examples for the 400V series.
Detailed explanation of the servo drive's front panel components and their functions.
Step-by-step guide for setting parameters using the front panel.
Explanation of various status indicators and displays on the panel.
General operational functions accessible via the panel.
Pre-operation checks on the motor and drive without load.
Correct procedure for applying power to the servo drive.
Procedure for testing motor operation in JOG mode without load.
Steps for trial running the motor in speed mode without load.
Steps for trial running the motor in position mode without load.
General procedure for tuning the servo system.
Description of single, dual, and multi-control modes.
Detailed explanation of position control mode.
Detailed explanation of speed control mode.
Detailed explanation of torque control mode.
Explanation of dual mode operations.
Overview of the motion control capabilities of the ASDA-A2 series.
Information about system parameters, monitoring variables, and data arrays.
Explanation of the different motion axes and their attributes.
Detailed description of the PR (Procedure) mode.
How to perform homing operations in PR mode.
Overview of parameters related to motion control and PR mode settings.
Detailed explanation of the Electronic Cam (E-Cam) function.
Explanation of parameter grouping and naming conventions.
A comprehensive list of parameters, their abbreviations, functions, and related sections.
Detailed descriptions of various parameters, categorized by group.
List of servo drive alarms, their descriptions, corresponding DO signals, and servo status.
Troubleshooting for CANopen communication alarms and corrective actions.
Troubleshooting for motion control related alarms and corrective actions.
Detailed breakdown of common causes and corrective actions for various alarms.
General corrective actions for various alarm codes.
To Next Page
