58
“Looking For 4580 Module...” will be displayed on the keypad being used for programming when
this module type has been selected. The Escort 4580 Voice Prompting Module does not require a
tamper to be enrolled. This module type will “auto-enroll” itself onto the system once this selection
has been made. If the enroll of the module is successful then the keypad will display the
message “4580 Mod 01 Enrolled”. Press any key and the display will prompt with “Select (01)” on
the top line of the display, and on the bottom line will be the partition name that the module is
going to be assigned to. Options 01 through 08 are partition assignments and option 09 is Global
Module. The Escort 4580 will behave as a keypad on the partition it is assigned to. Only one 4580
module may be used on the system at a time. If the module can not be found by the control
panel, the message “4580 Mod Not Present” will be displayed on the keypad. Recheck the
connection between the control panel and the Escort 4580 referring to the module work sheet.
Delete Module
Before removing any module from the system be sure to first delete the module from the system. To
delete a module from the system first select the module class (e.g. LCD4500). Then select the module
number (e.g. Module #05) to be removed from the system, by either scrolling to the selected module
an d pressing the [Q] key or entering the digits directly (LCD4500 #05) would be deleted.
Note: If the module number is not know use CONFIRM MODULE to verify the Module
number before attempting to delete the module. The PC4700 Fire Module and the Escort
4580 Voice Prompting Module will not require the module number to be entered in order to
delete the module.
DVAC module must be deleted before removing from the system.
Confirm Module
This is used to identify a module on the system in case the module number has been lost and
further programming on that module is desired. Once the tamper is created the keypad display
will indicate the module number.
Note: The PC4700 and Escort 4580 Confirm without Keypresses or Tamper being performed.
RF Zone Options
RF Zone option refer the wireless zone modules that may be enrolled onto the system when using
the PC4164. This section will only be made available when the PC4164 is enrolled. This section
will describe the procedure for enrolling, deleting, placing and defaulting the PC4164 zones.
This section is used to assign a wirless zone to the PC4164. Unlike the PC4108 and the PC4116
zone must be assigned to the module and then assigned to the partition. “Enroll RF Zone” allows
the PC4164 know which zones belong to the module. When this section is entered the display will
read “Enroll RF Zone” on the top line of the Display and “Serial # [ ]” on the bottom line of the LCD.
Enter in the 5 digit serial number (SN:XXXXX) found on the bottom of the zone transmitter section.
Once the serial number has been entered the keypad display will show the “RF Zone enrolled” on
the top line to the display and “Zone XXX” on the bottom line of the display (where XXX is the actual
zone number the module is assigned to on the control panel). As the zones are enrolled the serial
number will fill the first available empty position. Example if zones 17 to 23 are used but zone 20 is
empty the next zone that is enrolled will be placed in zone number 20 position.
Note: The PC4164 supports wireless door contacts and motion detectors.
This section allow the wireless zone to be deleted from the PC4164. When this section is entered
the display will read “Serial# [ ]” on the top line of the display and the zone label on the bottom
line of the display. Use the [<][>] keys to scroll to the zone that is to be deleted then press the
[Q] key. The bottom line of the display will then read “Zone Deleted”. Adding a new zone to the
system will automatically fill this location with the new serial number.
This section allow one RF zone to be replace with another RF Zone. All programming that was
used with the old zone will be used with the new zone. When this section is entered the display
will read “Serial# [ ]” on the top line of the display and the zone label on the bottom line of the
display. Use the [<][>] keys to scroll to the zone that is to be replaced then press the [Q] key.
The top line of the display will then read “With RF Zone”, the bottom line of the display will read
“Serial# [ ]”. Enter the serial number of the zone to replace the selected zone.
MODULE HARDWARE
ENROL L MODULE
ESCORT 4580
(6)
DELETE MODULE
(1)
CONFIRM MODULE
(2)
RF ZONE OPTIONS
(3)
ENROLL RF ZONE
(0)
DELETE RF ZONE
(1)
REPLACE RF ZONE
(2)
To Next Page
Loading...
