32
SYSTEM AREA
COMMUNICATOR
REPORTING CODES
LINKS MODULE
• 2 Wire TBL Rest. - This trouble restoral code will be sent when the 2 wire smoke detector
zone trouble has restored.
• Waterflow TBL - This trouble code will be sent when the Waterflow detector zone has a
trouble (WFA or WFB loops are open) condition.
• Waterflw TBL Rest - This trouble restoral code will be sent when the Waterflow detector zone
trouble has restored.
• Ground Fault - This trouble code will be sent when the earth ground connection detects a
ground fault. Note: The Ground terminal must not be connect to the COMBUS ground,
Connecting earth ground to the COMBUS ground will interfere with system performance an
generate a Ground Fault Trouble.
• Ground FLT Rest. - This trouble code will be sent when the earth ground fault connection is
restored.
Police Code Alarm is an alarm notification feature such that when a zone on an armed partition
goes into alarm and the zone transmits a zone alarm (or tamper alarm) reporting code a timer
(Police Code Time - see System Times) will being. If during this time (60 minutes by default) a
second zone goes into alarm, this zone will transmit its alarm reporting code followed by the
partition(s) Police Code Alarm Reporting code (there is a Police Code Alarm reporting code for
each partition). A second police code will only be sent once the police code restore has been
transmitted for that partition (see Police Code Restoral). Police Code Alarm will only function for
burglary zones and only while the partition is armed. This includes 24 hour Burg zones (24 Bell,
Bell/Buzz, and Buzzer, latching 24 Hour). The only zone that will activate the police code are the
following; Standard Delay; Auxiliary Delay; Instant; Interior; Interior Home Away; Delay Home
Away; 24 Hr Bell; 24 Hr Bell/Buzz; 24 Hr Buzzer; and the Latching 24 hr
The Police Code Restoral will be transmitted when the partition is disarmed or when using
Restorals Follow Bell Time-Out (BTO) when the bell times out.. A second police code will only be
sent once the Police Code Restore has been transmitted for that partition.
Links Module
These section options are relevant to the Links operation.
Note: Dial Tone Search must be included in the land phone number. See ‘Main Item’ for programming details.
Phone Number 1. If the Links module is enabled on the PC4010 this number will be used to back
up the land line first number should the telephone line fail.
Phone Number 2. If the Links module is enabled on the PC4010 this number will be used to back
up the land line second number should the telephone line fail.
Phone Number 3. If the Links module is enabled on the PC4010 this number will be used to back
up the land line third number should the telephone line fail.
This number is used if downloading is to be done or backed up with the Links 1000 unit.
Enter the telephone number for computer if User Call Up, Periodic DLS or DLS Callback is
enabled. See “PGM TEL NUMBER” for entering a telephone number and options when
programming the phone number.
Programming Telephone Numbers
Enter the telephone number the way you would on a telephone. The total number of digits including
the dial tone search and pauses must not exceed 31. Press the [Q] key to enter the telephone entry
options menu. A “D” for dial tone search is already programmed as the first digit.
Note: There must be a dial tone search programmed into the land line phone number for the links unit
to operate.
[0] Save [1] Dial tone [2] Pause 2 Seconds [3] Pause 4 Seconds
[4] DTMF [Q] [5] DTMF [#] [6] Previous Menu
[0] Save can be selected for the telephone number to be stored into the panel’s memory, or
simply press [#] when finished entering the number.
POLICE CODE REST
(26)
LINKS MODULE
(4)
1ST NUMBER
(0)
2ND NUMBER
(1)
3RD NUMBER
(2)
DLS NUMBER
(3)
POLICE CODE ALARM
(25)
To Next Page
Loading...
