5.5. EKB3W Keypad and User/Master Code
ATTENTION: The user will be able arm/disarm only the rst two system partitions using EKB3W keypad. Partition 3 and Partition 4 are
NOT supported by EKB3W keypad.
Illuminated indicator on EKB3W keypad indicates that no violated zones and/or tampers are present, therefore the partition is ready for
arming. If the indicator is not illuminated, the partition is unready for arming, therefore the user must restore all violated zones and/or
tampers before arming the partition. Alternatively, the violated zones can be bypassed (see 8. BYPASSING AND ACTIVATING ZONES),
disabled (please contact your alarm system installer to set up this parameter) or a Force attribute enabled (please contact your alarm
system installer to set up this parameter), while the tampers can be disabled (please contact your alarm system installer to set up this
parameter). Indicator will illuminate or ash if system fault (-s) exist (see 13. INDICATION OF SYSTEM FAULTS).
The system will arm/disarm the partition corresponding to the one that user/master code and the keypad are assigned to. For example, if
User code 4 is assigned to Partition 2, while EKB3W keypad is assigned to Partition 1, the user will be able to arm/disarm only Partition 2 by
entering User code 4. For more details on how to set the keypad partition and user/master code partition, please refer to 3.3. Assigning
User and Master Code Partition and contact your alarm system installer
5.5.1. Arming the System
• Non-partitioned system – When a valid user/master code is entered, the system will initiate exit delay, the keypad’s buzzer will emit
short beeps and the indicator will light ON. When the system is successfully armed, the keypad’s buzzer will silent down.
Arm the system
Enter user/master code:
uumm
Value: uumm – 4-digit user or master code.
Example:
2 2 2 2
• Partitioned system - arming a single partition – To arm a dierent partition than the keypad is assigned to, use keypad partition
switch feature (by default – disabled; please, contact your alarm system installer to set up this parameter) before the disarming process.
Switch keypad parti-
tion
Hold the
1 2
key and release it after 3 short beeps:
Value:
1 2
key – partition number 1... 2 respectively.
Once the partition is switched, indicator will light ON in EKB3W keypad’s section A (= Partition 1) or B (= Partition 2) and by entering a
valid user/master code, the system will initiate exit delay, the keypad’s buzzer will emit short beeps and the indicator will light ON in
the respective EKB3W keypad’s section. When the system is successfully armed, the keypad’s buzzer will silent down and the user will be
notied by SMS text message.
Arm the system
Enter user/master code:
uumm
Value: uumm – 4-digit user or master code.
Example:
2 2 2 2
To arm multiple partitions, please arm the partitions one by one by following the aforementioned procedure.
NOTE: If the user fails to enter a correct user/master code 10 times in a row, the system will block the keypad for 2 minutes. While the
keypad is blocked, the system prevents from entering any user/master code. The keypad will automatically unblock once the 2-minute
time has expired.
5.5.2. Cancelling System Arming
To cancel the arming process, enter the user/master code again during exit delay countdown.
5.5.3. Disarming the System and Turning OFF the Alarm
To disarm and turn OFF the alarm, enter any out of 29 available 4-digit user codes or master code using the number keys on the keypad. By
default, the system disarming process is as follows:
• Non-partitioned system – When a valid user/ master code is entered, indicator will light OFF and the user will be notied by SMS
text message.
Disarm the system and
turn OFF the alarm
Enter user/master code:
uumm
Value: uumm – 4-digit user or master code.
Example:
2 2 2 2
• Partitioned system - disarming a single partition – To disarm and turn OFF the alarm in a dierent partition than the keypad
is assigned to, use keypad partition switch feature (by default – disabled; please, contact your alarm system installer to set up this
To Next Page
Loading...
