DISPLAY (continued)
ASSIGN LINE 1
(p. 67)
FLOW RATE
– TOTAL VOLUME –
BATCH QUANTITY – BATCH UPWARDS –
BATCH DOWNWARDS – BATCH CYCLE
Your setting: ............................................
ASSIGN LINE 2
(p. 67)
OFF
FLOW RATE
TOTAL VOLUME
TOTAL OVERFLOW
BATCH QUANTITY
BATCH UPWARDS
BATCH DOWNWARDS
BATCH CYCLE
Your setting: ............................................
DISPLAY DAMPING
(p. 68)
max. 2-digit number: 0...99 s
Factory setting:
1 s
Your setting: ............................................
DISPLAY
FORMAT
(p. 68)
x.xxxx
5 significant digits
x.xxx 4 significant digits
x.xx 3 significant digits
Your setting: ............................................
LCD CONTRAST
(p. 68)
IIIIIIIIIIII ...........
A change in contrast is immediately seen
on the bar graph
LANGUAGE
(p. 68)
ENGLISH – DEUTSCH –
FRANCAIS – ESPANOL –
ITALIANO – NEDERLANDS –
DANSK – NORSK – SVENSKA –
SUOMI – BAHASA INDONESIA –
JAPANESE (in original alphabet)
Your setting: ............................................
COMMUNICATION
PROTOCOL
(p. 69)
With “HART” communication module:
OFF
– HART
With “RS 485” communication module:
OFF
– RACKBUS RS 485
Communication module: .........................
Your setting: ............................................
BUS ADDRESS
(p. 69)
max. 2-digit number:
0
...15 (HART);
0
...63 (RS 485)
Your setting: ............................................
ASSIGN
AUX. INPUT
(S. 69)
For “Pulsed mode”:
RESET TOTALIZER
BATCHING
For “Level mode”:
DUAL RANGE MODE
POS. ZERO RETURN
Your setting: ............................................
COMMUNICATION (continued)
START PULSE
WIDTH
(S. 71)
max. 3-digit number:
20
...100 ms
Your setting: ............................................
SYSTEM CONFIG.
(p. 71)
Display (only with “RS 485” communication
module)
RS 485 / CURRENT
RS 485 / FREQUENCY
AUX. INPUT / CURRENT
AUX. INPUT / FREQ.
PROCESSING PARAMETERS
LOW FLOW
CUTOFF
(p. 72)
5-digit floating point: e.g. 15.000 dm
3
/min
Factory setting:
dependent
on diameter
Your setting: ............................................
NOISE
SUPPRESS.
(p. 72)
OFF – LOW –
MEDIUM
– HIGH
Your setting: ............................................
EMPTY PIPE
DET.
(p. 73)
Two functions:
– Switching on/off “Empty pipe detection”
– Start empty or full pipe adjustment
OFF
– ON – EMPTY PIPE ADJ. –
FULL PIPE ADJUST
Your setting: ............................................
EPD
RESPONSE TIME
(p. 74)
1s
– 2 s – 5 s – 10 s – 30 s – 60 s
Your setting: ............................................
MEASURING
MODE
(p. 75)
UNIDIRECTIONAL –
BIDIRECTIONAL
Your setting: ............................................
FLOW DIRECTION
(p. 75)
FORWARD
1)
– REVERSE
2)
1)
Positive flow according to the arrow
on the nameplate
2)
Positive flow in the opposite direction
to the arrow on the nameplate
Your setting: ............................................
FUNCTION ECC
(p. 75)
ON
– OFF
Your setting: ............................................
RECOVERY TIME
ECC
(p. 76)
max. 3-digit number: 1...255 s
Factory setting:
5s
Your setting: ............................................
AMPLIFIER MODE
(p. 76)
NORMAL
(automatic control)
MODE 1 (v = 0...>12 m/s)
MODE 2 (v = 0...12 m/s)
MODE 3 (v = 0... 4 m/s)
MODE 4 (v = 0... 1 m/s)
Your setting: ............................................
DELAY
(p. 76)
max. 4-digit number: 10...1000
Factory setting:
10
Your setting: ............................................
Promag 33 10 Functions at a Glance
Endress+Hauser 119
To Next Page
Loading...
