ESAB Cutmaster 80

To Next Page

To Previous Page

ESAB CUTMASTER 80

Manual 0-5396 GENERAL INFORMATION

This page intentionally blank.

Main Page

Default Chapter5
- Declaration of Conformity5
- Table of Contents6
Section 1: Safety10
- Safety Precautions10
Раздел 1: Безопасност12
Část 1: Bezpečnostní14
Sektion 1: Sikkerhedsforanstaltninger16
Kapitel 1: Sicherheit18
Sección 1: Seguridad20
PEAÜKK 1: Ohutus22
KAPPALE 1: Turvallisuus24
Chapitre 1 : Sécurité26
SECTION 1: Važne Sigurnosne28
Fejezet: Biztonsági30
Sezione 1: Sicurezza32
SKYRIUS. Saugos34
Nodaļa : Drošības36
Hoofdstuk 1: Veiligheid38
AVSNITT 1: Sikkerhet40
Rozdział 1: Bezpieczeństwo42
SECÇÃO 1: Segurança44
Secţiunea 1: Securitate46
Раздел 1, Правила Техники48
Časť 1: Bezpečnostné Pokyny50
Razdelek 1 - Varnost52
Avsnitt 1: Säkerhet54
Section 2 System: Introduction57
- How to Use this Manual57
- Equipment Identification57
- Receipt of Equipment57
- Power Supply Specifications58
- Input Wiring Specifications59
- Power Supply Features60
Section 2 Torch: Introduction61
- 01 Scope of Manual61
- 02 General Description61
- 03 Specifications61
- 04 Options and Accessories62
- 05 Introduction to Plasma62
Section 3 System: Installation65
- Unpacking65
- Lifting Options65
- Primary Input Power Connections65
- Gas Connections66
Section 3 Torch: Installation69
- 01 Torch Connections69
- 02 Setting up Mechanical Torch69
Section 4 System: Operation71
- Front Panel Controls / Features71
- Preparations for Operation72
Section 4 Torch: Operation75
- 01 Torch Parts Selection75
- 02 Cut Quality75
- 03 General Cutting Information76
- 04 Hand Torch Operation77
- 05 Gouging80
- T.05 Gouging80
- 06 Mechanized Torch Operation81
- 07 Parts Selection for Manual and Mechanized Torch Cutting82
  - T.08 Recommended Cutting Speeds for Mechanized Torch with Exposed Tip83
  - T.09 Recommended Cutting Speeds for Mechanized Torch with Shielded Tip86
Patent Information90
Section 5 System: Service93
- General Maintenance93
- Maintenance Schedule94
- Common Faults94
- Fault Indicator95
- Basic Troubleshooting Guide96
- Power Supply Basic Parts Replacement98
Section 5 Torch: Service101
- 01 General Maintenance101
- 02 Inspection and Replacement of Consumable Torch Parts102
Section 6: Parts Lists103
- Introduction103
- Ordering Information103
- Power Supply Replacement103
- Replacement Power Supply Parts103
- Options and Accessories104
- Replacement Parts for Hand Torch105
- Replacement Parts - for Machine Torches with Unshielded Leads106
- Replacement Shielded Machine Torch Leads Assemblies108
- Torch Consumable Parts (SL60)109
- Torch Consumable Parts (SL100)110
Appendix 1: Sequence of Operation (Block Diagram111
Appendix 2: Data Tag Information112
Appendix 3: Torch Pin - out Diagrams113
Appendix 4: Torch Connection Diagrams114
Appendix 5: System Schematic, 400V Units116
Revision History118

ESAB Cutmaster 80 - Page 56

Table of Contents

Related product manuals