Name: EUTECH INSTRUMENTS pH 600
Brand: EUTECH INSTRUMENTS
Rating: 4 (1 reviews)

To Next Page

To Previous Page

1.3 Attaching the Belt

To attach the safety belt:

1. Use a Phillips screw driver to remove the four screws holding the battery

cover.

2. Insert the safety belt through the two slots as indicated below.

3. Screw the battery cover back on. Note the ▲UP symbol marked on the

cover.

4. Insert your palm between the belt and the body of the meter and adjust the

hook & loop fastener.

Note the correct side

of the belt

Battery Cover

Hook & Loop

fastener

Default Chapter5
- Table of Contents5
General Guide9
Overview for All Meters11
- About the Meters11
  - Display Overview11
  - Key Functions11
- Inserting Batteries12
  - Inserting Batteries for the First Time12
  - Changing Batteries Subsequently12
- Attaching the Belt13
- Connecting Peripherals14
  - Probes (Ph/Conductivity/Do)14
  - Protective Rubber Boot15
System Setup Mode for All Meters16
- About Setup Mode16
- Accessing Setup Mode16
- Setup Selection: System Settings17
- Accessing Setup Mode When Password Protection Enabled23
- Modifying Setup Parameters24
Calibration Mode for All Meters25
- About Calibration25
- About Conductivity/ Resistivity/ TDS/ Salinity Calibration25
- Preparing the Meter for Calibration25
- Accessing Calibration Mode27
  - Accessing Calibration Mode When Password Protection Enabled27
Measurement Mode for All Meters29
- About Measurement Mode29
  - Accessing Functions29
- Taking Measurements30
- Automatic Temperature Compensation (ATC)31
  - Manual Temperature Compensation (MTC)31
- Alarm Set Point (for Ph/Conductivity/Do)32
- Calibration Due (CAL-DUE) Indicator (for Ph/Conductivity/Do)32
Transferring and Printing Data32
- Cybercomm 600 Data Acquisition Software32
- Working with Memory Functions - Auto Data Logging32
Technical Specifications37
Accessories41
Warranty & Return Policy42
- Warranty42
- Return of Goods42
- Guidelines for Returning Unit for Repair43
Temperature44
Temperature Setup46
Temperature Calibration46
- About Temperature Calibration46
- Temperature Calibration for ATC Mode47
- Temperature Calibration for MTC Mode48
Temperature Measurement48
Ph Setup52
Ph Calibration53
- About Ph Calibration53
- Ph Buffer Group for Calibration and Auto-Recognition54
  - Ph Calibration Points54
- Ph Calibration with a Standard Buffer54
  - To Start Ph Calibration54
- Ph Calibration with a User-Defined Buffer56
- Calibration Report57
  - To View Calibration Report57
- Average Slope Indicator of Ph Probe58
Ph Measurement Mode58
- Resolution of Ph Reading58
- Indicators in Ph Measurement Screen59
MV Setup Mode62
MV Calibration Mode62
- MV Calibration with a Standard ORP Calibration Solution62
- Calibration Report63
  - To View Calibration Report63
MV Measurement Mode63
- Indicators in MV Measurement Mode63
Ion66
Ion Setup68
Ion Calibration Mode68
- About Ion Calibration68
- Calibration Report70
  - To View Calibration Report70
Ion Measurement Mode71
- Changing Unit of Measurement71
- Indicators in Ion Measurement Mode71
Conductivity72
Conductivity Setup74
Conductivity Calibration Mode76
- Conductivity Calibration Points76
- Cell Constant76
- Normalization Temperature ( ° C)76
- Linear Temperature Coefficient76
- Pure Water Coefficient77
- To Begin Calibration77
- Manual Calibration78
- Automatic Calibration (for Conductivity Calibration)78
- Calibration Report80
  - To View Calibration Report80
Conductivity Measurement Mode80
- Indicators in Conductivity Measurement Screen80
Tds83
TDS Setup85
TDS Calibration Mode87
- TDS Calibration Report88
  - To View Calibration Report88
TDS Measurement Mode89
- Indicators in TDS Measurement Mode89
About TDS90
- Calculating TDS Conversion Factor90
- Calculating Temperature Coefficients90
Salinity91
Salinity Setup93
Salinity Calibration Mode94
- Salinity Calibration Report96
  - To View Salinity Report96
Salinity Measurement Mode97
- Indicators in Salinity Measurement Mode97
Resistivity99
Resistivity Setup101
Resistivity Calibration Mode103
- Resistivity Calibration Report104
  - To View Calibration Report104
Resistivity Measurement Mode105
- Indicators in Resistivity Measurement Mode105
Dissolved Oxygen107
PART a - % Saturation Mode109
O2 % - DO Saturation Setup109
DO Calibration in % Saturation Mode (with ATC)111
- About DO(%) and DO (Mg/L) Calibration111
- To Calibrate 100% Saturation111
- To Calibrate 0% Saturation113
  - DO Calibration Report114
  - To View Calibration Report114
- Saturation Offset Adjustment115
- Set Barometer Pressure Range and Barometric Pressure Units115
- Pressure Compensation115
Percentage Saturation (%) Measurement Mode115
- Indicators in Percentage Saturation Measurement Mode115
PART B - Concentration (Mg/L) (Ppm) Mode116
O2 Mg/L (Ppm) - DO Concentration Setup116
DO Calibration in Mg/L Mode or Ppm Concentration Mode119
- Concentration Calibration Report120
  - To View Calibration Report120
- Set Salinity121
  - Auto Salinity Compensation121
Concentration in Measurement Mode121
- Indicators in Concentration Measurement Screen121
- Dissolved Oxygen Probe122

Questions and Answers:

Need help?

Do you have a question about the EUTECH INSTRUMENTS pH 600 and is the answer not in the manual?

EUTECH INSTRUMENTS pH 600 Specifications

General

Brand	EUTECH INSTRUMENTS
Model	pH 600
Category	Measuring Instruments
Language	English

Related product manuals

EUTECH INSTRUMENTS PCSTESTR 35

2 pages

EUTECH INSTRUMENTS 2700

60 pages

EUTECH INSTRUMENTS Ion 700

20 pages

EUTECH INSTRUMENTS TN-100

32 pages

EUTECH INSTRUMENTS 450 Series

2 pages

EUTECH INSTRUMENTS pH 600 User Manual

Table of Contents

Questions and Answers:

EUTECH INSTRUMENTS pH 600 Specifications

Related product manuals