EUTECH INSTRUMENTS pH 600

To Next Page

To Previous Page

TEMPERATURE

PARAMETER GUIDE

i. Temperature Setup Mode

ii. Temperature Calibration – ATC and MTC Mode

iii. Temperature Measurement Mode

FOR ALL MODELS :

pH 600/ 610/ 620 COND 600/610

DO 600 PC 650

PD 650 CD 650

PCD 650

Main Page

Default Chapter5
- Table of Contents5
General Guide9
Overview for All Meters11
- About the Meters11
  - Display Overview11
  - Key Functions11
- Inserting Batteries12
  - Inserting Batteries for the First Time12
  - Changing Batteries Subsequently12
- Attaching the Belt13
- Connecting Peripherals14
  - Probes (Ph/Conductivity/Do)14
  - Protective Rubber Boot15
System Setup Mode for All Meters16
- About Setup Mode16
- Accessing Setup Mode16
- Setup Selection: System Settings17
- Accessing Setup Mode When Password Protection Enabled23
- Modifying Setup Parameters24
Calibration Mode for All Meters25
- About Calibration25
- About Conductivity/ Resistivity/ TDS/ Salinity Calibration25
- Preparing the Meter for Calibration25
- Accessing Calibration Mode27
  - Accessing Calibration Mode When Password Protection Enabled27
Measurement Mode for All Meters29
- About Measurement Mode29
  - Accessing Functions29
- Taking Measurements30
- Automatic Temperature Compensation (ATC)31
  - Manual Temperature Compensation (MTC)31
- Alarm Set Point (for Ph/Conductivity/Do)32
- Calibration Due (CAL-DUE) Indicator (for Ph/Conductivity/Do)32
Transferring and Printing Data32
- Cybercomm 600 Data Acquisition Software32
- Working with Memory Functions - Auto Data Logging32
Technical Specifications37
Accessories41
Warranty & Return Policy42
- Warranty42
- Return of Goods42
- Guidelines for Returning Unit for Repair43
Temperature44
Temperature Setup46
Temperature Calibration46
- About Temperature Calibration46
- Temperature Calibration for ATC Mode47
- Temperature Calibration for MTC Mode48
Temperature Measurement48
Ph Setup52
Ph Calibration53
- About Ph Calibration53
- Ph Buffer Group for Calibration and Auto-Recognition54
  - Ph Calibration Points54
- Ph Calibration with a Standard Buffer54
  - To Start Ph Calibration54
- Ph Calibration with a User-Defined Buffer56
- Calibration Report57
  - To View Calibration Report57
- Average Slope Indicator of Ph Probe58
Ph Measurement Mode58
- Resolution of Ph Reading58
- Indicators in Ph Measurement Screen59
MV Setup Mode62
MV Calibration Mode62
- MV Calibration with a Standard ORP Calibration Solution62
- Calibration Report63
  - To View Calibration Report63
MV Measurement Mode63
- Indicators in MV Measurement Mode63
Ion66
Ion Setup68
Ion Calibration Mode68
- About Ion Calibration68
- Calibration Report70
  - To View Calibration Report70
Ion Measurement Mode71
- Changing Unit of Measurement71
- Indicators in Ion Measurement Mode71
Conductivity72
Conductivity Setup74
Conductivity Calibration Mode76
- Conductivity Calibration Points76
- Cell Constant76
- Normalization Temperature ( ° C)76
- Linear Temperature Coefficient76
- Pure Water Coefficient77
- To Begin Calibration77
- Manual Calibration78
- Automatic Calibration (for Conductivity Calibration)78
- Calibration Report80
  - To View Calibration Report80
Conductivity Measurement Mode80
- Indicators in Conductivity Measurement Screen80
Tds83
TDS Setup85
TDS Calibration Mode87
- TDS Calibration Report88
  - To View Calibration Report88
TDS Measurement Mode89
- Indicators in TDS Measurement Mode89
About TDS90
- Calculating TDS Conversion Factor90
- Calculating Temperature Coefficients90
Salinity91
Salinity Setup93
Salinity Calibration Mode94
- Salinity Calibration Report96
  - To View Salinity Report96
Salinity Measurement Mode97
- Indicators in Salinity Measurement Mode97
Resistivity99
Resistivity Setup101
Resistivity Calibration Mode103
- Resistivity Calibration Report104
  - To View Calibration Report104
Resistivity Measurement Mode105
- Indicators in Resistivity Measurement Mode105
Dissolved Oxygen107
PART a - % Saturation Mode109
O2 % - DO Saturation Setup109
DO Calibration in % Saturation Mode (with ATC)111
- About DO(%) and DO (Mg/L) Calibration111
- To Calibrate 100% Saturation111
- To Calibrate 0% Saturation113
  - DO Calibration Report114
  - To View Calibration Report114
- Saturation Offset Adjustment115
- Set Barometer Pressure Range and Barometric Pressure Units115
- Pressure Compensation115
Percentage Saturation (%) Measurement Mode115
- Indicators in Percentage Saturation Measurement Mode115
PART B - Concentration (Mg/L) (Ppm) Mode116
O2 Mg/L (Ppm) - DO Concentration Setup116
DO Calibration in Mg/L Mode or Ppm Concentration Mode119
- Concentration Calibration Report120
  - To View Calibration Report120
- Set Salinity121
  - Auto Salinity Compensation121
Concentration in Measurement Mode121
- Indicators in Concentration Measurement Screen121
- Dissolved Oxygen Probe122

EUTECH INSTRUMENTS pH 600 - Temperature

Table of Contents

Related product manuals