evertz 5600MSC - Page 8

Model 5600MSC Master Clock/SPG Manual
viii
Revision 1.6
3.3.4. Modem Status...................................................................................................................3-6
3.3.5. NTP Messages ................................................................................................................. 3-6
3.3.6. LTC 1 Output Power Status Messages ............................................................................ 3-6
3.3.7. Power Supply Status Messages....................................................................................... 3-7
3.3.8. GPI Input Supply Status Messages.................................................................................. 3-7
3.3.9. Cooling Fan Status Messages.......................................................................................... 3-7
3.3.10. Synchro Status Messages................................................................................................3-7
3.3.11. Flashing Leds ...................................................................................................................3-7
3.4. AN OVERVIEW OF THE SETUP MENU SYSTEM ..................................................................... 3-7
3.5. CONFIGURING THE INPUT REFERENCES .............................................................................. 3-9
3.5.1. Configuring the Frequency Reference.............................................................................. 3-9
3.5.2. Configuring the Time Reference..................................................................................... 3-12
3.5.3. Setting The VITC Reader Line........................................................................................3-14
3.5.4. Configuring the Genlock Capture Range........................................................................3-14
3.5.5. Synchronizing The System Master Oscillator to the Frequency Reference Immediately3-15
3.5.6. Configuring the Lock Speed ........................................................................................... 3-16
3.6. CONFIGURING THE OUTPUTS................................................................................................ 3-17
3.6.1. Configuring the LTC Outputs.......................................................................................... 3-17
3.6.1.1. Selecting Normal or Powered LTC Output (LTC1 output only).............................. 3-18
3.6.1.2. Setting the LTC Output Rate.................................................................................. 3-18
3.6.1.3. Selecting when the LTC Time is Synchronized to the System Time......................3-19
3.6.1.4. Synchronizing The LTC Time to the System Clock Immediately........................... 3-19
3.6.1.5. Synchronizing All The LTC and VITC Times to the System Clock Immediately .... 3-20
3.6.1.6. Setting The LTC Offset .......................................................................................... 3-20
3.6.1.7. Setting The LTC Time Zone................................................................................... 3-20
3.6.1.8. Enabling Daylight Saving Time Compensation on the LTC Output ....................... 3-21
3.6.1.9. Enabling the LTC Output Parity Bit........................................................................ 3-21
3.6.1.10. Enabling LTC Output Colour Frame Bit ................................................................. 3-21
3.6.1.11. Setting The LTC Output Level ...............................................................................3-21
3.6.2. Configuring the Video Sync Outputs............................................................................... 3-21
3.6.2.1. Selecting the Clock frequency for Each Bank of the Sync Outputs ....................... 3-22
3.6.2.2. Selecting the Standard of the Sync Outputs.......................................................... 3-22
3.6.2.3. Configuring the VITC Generator for the Colour Black Outputs..............................3-23
3.6.2.3.1. Enabling VITC on the Video Output.............................................................. 3-23
3.6.2.3.2. Selecting the VITC Lines............................................................................... 3-24
3.6.2.3.3. Enabling Drop Frame Compensation on the VITC Output............................ 3-24
3.6.2.3.4. Enabling Colour Frame Compensation on the VITC Output......................... 3-25
3.6.2.3.5. Selecting when the VITC Time is Synchronized to the System Time ........... 3-25
3.6.2.3.6. Synchronizing The VITC Time to the System Clock Immediately................. 3-26
3.6.2.3.7. Synchronizing The LTC and VITC Times to the System Clock Immediately 3-26
3.6.2.3.8. Setting The VITC Offset................................................................................ 3-26
3.6.2.3.9. Setting The VITC Time Zone ........................................................................3-27
3.6.2.3.10. Enabling Daylight Saving Time Compensation on the VITC Output............ 3-27
3.6.2.3.11. Enabling Ten Field Pulse............................................................................. 3-28
3.6.2.4. Setting The Phase of the Sync Outputs................................................................. 3-28
3.6.3. Configuring the Analog Video Test Generator Output (STG Option only)...................... 3-30
3.6.3.1. Selecting the Standard of the Analog Video Test Generator Output ..................... 3-30
3.6.3.2. Setting The Phase of the Analog Video Test Generator Output............................ 3-30
USO RESTRITO