FDP EX-CPL - Default Chapter; Table of Contents

Page 2 of 91
Rev. 4.
2
0
INDEX
PART 1 DETAILS..........................................................................................................................................................................................6
1.1 GENERAL CHARACTERISTICS ...................................................................................................................................................6
1.2 POINT ADDRESSING AND ACQUISITION .................................................................................................................................8
PART 2 CONTROL PANEL INSTALLATION..........................................................................................................................................9
2.1 SAFETY REQUIREMENTS ............................................................................................................................................................9
2.2 CONNECTING THE CONTROLPANEL TO THE MAIN POWER LINE 230VCA......................................................................9
2.3 FUSES...............................................................................................................................................................................................9
2.4 FIXING THE CONTAINER...........................................................................................................................................................10
2.4.1 Cable arrangement...............................................................................................................................................................10
2.4.2 Observation ..........................................................................................................................................................................10
2.4.3 Assembly...............................................................................................................................................................................11
2.5 CONNECTION...............................................................................................................................................................................11
2.5.1 The circuits of the detection..................................................................................................................................................12
2.5.2 Fire alarm siren output.........................................................................................................................................................13
2.5.3 Output for alarm siren fault..................................................................................................................................................14
2.5.4 Outputs of auxiliary relays no supervised.............................................................................................................................15
2.5.5 Open Collector outputs.........................................................................................................................................................15
2.5.6 Auxiliary output 24 Vdc........................................................................................................................................................15
2.5.7 Serial ports ...........................................................................................................................................................................15
2.5.8 Connection to the power supply............................................................................................................................................16
2.5.9 Battery connections ..............................................................................................................................................................16
2.6 LOOP SECTION.............................................................................................................................................................................16
2.7 LOCATION OF GROUND SHUNT IN THE CONTROL PANEL.................................................................................................16
2.8 MAINTENANCE ...........................................................................................................................................................................17
2.8.1 Daily control.........................................................................................................................................................................17
2.8.2 Weekly control......................................................................................................................................................................17
2.8.3 Four-monthly control............................................................................................................................................................17
2.8.4 Yearly control.......................................................................................................................................................................17
2.8.5 Cleaning the Smoke Sensor...................................................................................................................................................17
PART 3 PRELIMINARY REMARKS FOR A CORRECT INSTALLATION ......................................................................................18
3.1 LINE CABLE TEST PROCEDURE BEFORE LOOP CONNECTION..........................................................................................18
3.1.1 Line continuity......................................................................................................................................................................18
3.1.2 Shielded ................................................................................................................................................................................18
3.1.3 Isolation between positive and negative of loop ...................................................................................................................18
3.1.4 Isolation between SHI / –LOOP and SHI / +LOOP .............................................................................................................18
3.1.5 Check of SHI short circuits at power supply line..................................................................................................................19
PART 4 ABOUT PROGRAMMING ..........................................................................................................................................................20
4.1 CONTROLS AND INFORMATION..............................................................................................................................................20
4.1.1 Control panel controls..........................................................................................................................................................20
4.1.2 Led indicators of the control panel.......................................................................................................................................21
4.2 HOW TO SELECT AN ITEM FROM THE MENU OF THE CONTROL PANEL.........................................................................22
4.3 PASSWORD MANAGEMENT......................................................................................................................................................23
4.4 ACCESS LEVELS..........................................................................................................................................................................23
4.4.1 Levels for users and installers ..............................................................................................................................................23
4.5 OUT OF SERVICE, FAULT, ALARM MESSAGES .....................................................................................................................24
4.5.1 General.................................................................................................................................................................................24
4.5.2 Silence ..................................................................................................................................................................................24
4.5.3 View Messages......................................................................................................................................................................24
4.5.4 Visualizing the event.............................................................................................................................................................26
4.5.5 Active outputs .......................................................................................................................................................................27
4.5.6 Alarm Reset ..........................................................................................................................................................................27
4.6 VISUALIZATION OF EVENTS ....................................................................................................................................................27
4.6.1 Main menu............................................................................................................................................................................27
4.6.2 Event menu ...........................................................................................................................................................................27
PART 5 FIRST CONFIGURATION OF CONTROL PANEL.................................................................................................................28
PART 6 LOOP PROGRAMMING .............................................................................................................................................................31
6.1 LOOP STARTING..........................................................................................................................................................................31
6.1.1 Main menu............................................................................................................................................................................31
6.1.2 Loop menu ............................................................................................................................................................................31
6.1.3 Loop start/restore (loop selection)........................................................................................................................................31
6.1.4 Loop start/restore procedure................................................................................................................................................32
6.1.5 Information...........................................................................................................................................................................32