Fischer Panda iControl3 - Table of Contents; Panda Icontrol3

20.10.22 Inhalt/Contents Seite/Page 1
Inhalt / Contents
Panda iControl3............................................................................................................................................ ....... 1
Current revision status................................................................................................................................ ....... 2
Hardware....................................................................................................................................................... ....... 2
2 Safety instructions for the Panda iControl3......................................................................................... ....... 3
2.1 Personnel........................................................................................................................................ ...... 3
2.2 Safety instructions .......................................................................................................................... ...... 3
3 General operation ................................................................................................................................... ....... 5
3.1 The Panda iControl3 panel ............................................................................................................. ...... 5
3.2 Starting preparation / Checks (daily) .............................................................................................. ...... 6
3.2.1 Marine version ................................................................................................................ ...... 6
3.2.2 Vehicle version ............................................................................................................... ...... 6
3.3 Operation ........................................................................................................................................ ...... 7
3.3.1 Switching the controller on and off ................................................................................. ...... 7
3.3.2 Default display screen .................................................................................................... ...... 8
3.3.3 Operating modes ............................................................................................................ ...... 9
3.3.3.1 Stand-by mode................................................................................................. ...... 9
3.3.3.2 Start-up mode .................................................................................................. ...... 9
3.3.3.3 Override mode ................................................................................................. .... 10
3.3.3.4 Operation mode ............................................................................................... .... 11
3.3.3.5 Panda i-Generator with electro-magnet Clutch (optional)................................ .... 12
3.3.3.6 Stop mode........................................................................................................ ..... 13
3.3.3.7 Autostart mode................................................................................................. .... 13
3.4 Set-up menu .................................................................................................................................. ..... 14
3.4.1 Submenu »Panel« .......................................................................................................... ..... 15
3.4.1.1 Setting the backlight (»Backlight« and »Dimtime«).......................................... .... 15
3.4.1.2 Setting the language (»Language«)................................................................. .... 17
3.4.1.3 Selecting the unit for temperature value outputs (»Units«).............................. ..... 18
3.4.1.4 Setting the network ID...................................................................................... .... 18
3.4.2 Submenu »Generator« ................................................................................................... ..... 19
3.4.2.1 Priming the fuel system (»Prime fuel«) ............................................................ ..... 20
3.4.2.2 Resetting the service interval (»Service«)........................................................ .... 20
3.4.2.3 Activating/deactivating the autostart function (»Autostart«)............................. .... 21
3.4.3 Submenu »Save« ........................................................................................................... ..... 23
3.5 iControl3 Emergency Stop ............................................................................................................. ..... 24
4 Installation ............................................................................................................................................... ..... 25
4.1 Personnel........................................................................................................................................ .... 25
4.1.1 Hazard warnings for installation ..................................................................................... .... 25
4.2 Disposal of the components ........................................................................................................... .... 26
4.2.1 Panda iControl3 panel with installation housing ............................................................. .... 27
4.2.2 Connectors and switches on the Panda iControl3 panel ................................................ .... 27
4.2.2.1 Terminal assignment of the 5-pin Phoenix socket ........................................... ..... 28
4.2.2.2 Terminal assignment of the automatic start socket.......................................... .... 28
4.2.2.3 Terminal assignment Fischer Panda CAN-Bus 2............................................. .... 28
4.2.2.4 Function of the double DIP Switch................................................................... ..... 29
4.3 Dimensions Panda iControl3 panel ............................................................................................... ..... 30
4.4 Wiring of the Panda iControl3 control unit ...................................................................................... .... 31
4.4.1 Terminal assignment of the 42-pin socket ...................................................................... ..... 32
4.5 Dimensions Panda iControl3 control unit ....................................................................................... ..... 33