Flexim FLUXUS WW - Default Chapter; Umfluxus_Wwv1-1 En, 2018

146 pages

To Next Page

To Previous Page

FLUXUS is a registered trademark of FLEXIM GmbH.

FLEXIM GmbH

Boxberger Straße 4

12681 Berlin

Germany

Tel.: +49 (30) 936 67 660

Fax: +49 (30) 936 67 680

E-mail: info@flexim.de

www.flexim.com

User manual for

FLUXUS WW

UMFLUXUS_WWV1-1EN, 2018-02-28

Firmware version: V6.28

Subject to change without prior notice.

Main Page

Default Chapter2
- Umfluxus_Wwv1-1En, 20182
- Table of Contents5
1 Introduction9
- Regarding this User Manual9
- Safety Instructions9
- Warranty9
2 Safety Instructions10
- General Safety Instructions10
- Intended Use10
- Not Intended Use11
- Safety Instructions for the User11
- Safety Instructions for the Operator11
- Safety Instructions for Electrical Work11
- Safety Instructions for Transport12
- Recommended Procedure in Hazardous Situations12
- Recommended Maintenance Intervals12
3 Handling13
- First Inspection13
- General Precautions13
- Cleaning13
4 General Principles14
- Measurement System14
- Measurement Principle14
- Measurement Arrangements18
5 Description of the Transmitter21
- Transmitter Design21
- Keyboard21
6 Measuring Point Selection23
- Acoustic Penetration23
- Undisturbed Flow Profile25
- Selection of the Measurement Arrangement Taking into Account the Measuring Range and the Measuring Conditions27
- Selection of the Sound Beam Plane Near an Elbow28
7 Installation29
- Location29
- Transmitter29
- Transducers32
8 Connection49
- Transducers50
- Power Supply62
- Outputs63
- Serial Interface64
- Sensor Module (SENSPROM)65
- SD Card (Optional)66
9 Start-Up of the Transmitter67
- Start-Up Settings67
- Switching on67
- Initialization68
- Display68
- Hotcodes70
- Language Selection71
- Interruption of the Power Supply71
10 Basic Measurement72
- Input of Pipe Parameters72
- Other Parameters74
- Selection of the Channels74
- Input of the Sound Path Number75
- Transducer Distance75
- Start of Measurement77
- Detection of the Flow Direction77
- Stop of Measurement77
11 Displaying Measured Values78
- Selection of the Physical Quantity and the Unit of Measurement78
- Toggling between the Channels78
- Adjustment of the Display79
- Status Line80
- Transducer Distance81
12 Advanced Measuring Functions82
- Damping Factor82
- Totalizer82
- Settings of the Noisetrek Parallel Beam Mode83
- Settings of the Hybridtrek Mode84
- Upper Limit of the Flow Velocity85
- Cut-Off Flow85
- Uncorrected Flow Velocity86
- Measurement of High Dynamic Flows (Fastfood Mode)86
- Calculation Channels87
- Change of the Limit for the Inner Pipe Diameter89
- Diagnosis by Means of the Snap Function90
- Program Code91
13 Data Logger and Transmission of Data92
- Data Logger92
- Data Transmission95
14 Settings100
- Time and Date100
- Dialogs and Menus100
- Measurement Settings103
- Setting the Contrast104
- Instrument Information104
15 Superuser Mode105
- Activation/Deactivation105
- Transducer Parameters105
- Defining Flow Parameters105
- Limit of the Signal Amplification107
- Upper Limit of the Sound Speed107
- Detection of Long Measurement Failures108
- Number of Decimal Places of the Totalizers108
- Manual Reset of the Totalizers109
- Display of the Totalizer Sum109
- Display of the Last Valid Measured Value109
- Display During the Measurement109
16 Outputs110
- Installation of an Output110
- Error Value Delay114
- Activation of an Analog Output115
- Activation of a Binary Output as a Pulse Output116
- Activation of a Binary Output as an Alarm Output116
- Behavior of the Alarm Outputs119
- Deactivation of the Outputs121
17 Troubleshooting122
- Problems with the Measurement122
- Measuring Point Selection123
- Maximum Acoustic Contact123
- Application Specific Problems123
- Large Deviations of the Measured Values124
- Problems with the Totalizers124
- Data Transmission124
Annex125
A Menu Structure125
B Units of Measurement136
C Reference141
D Conformity Declarations144

Flexim FLUXUS WW - Default Chapter; Umfluxus_Wwv1-1 En, 2018

Table of Contents

Related product manuals