Fujitsu CELSIUS M730 - User Manual

Questions and Answers

D
Dr. Marisa HallAug 7, 2025
Why Fujitsu CELSIUS M730 Desktop power indicator remains off?
- C
  Crystal RichardsonAug 8, 2025
  The power indicator might remain off on your Fujitsu Desktop due to a faulty mains voltage supply or an overloaded internal power supply. First, ensure the power cable is correctly plugged into the device and a grounded mains outlet, and that the main switch at the rear is set to the "I" position, then switch the device on. If that doesn't work, pull the power plug out, wait about 3 minutes, plug it back into a grounded outlet, and switch the device on again.
T
timothyloweAug 14, 2025
What to do if Fujitsu CELSIUS M730 Desktop monitor remains blank?
- H
  Holly BennettAug 14, 2025
  If your Fujitsu Desktop monitor remains blank, there are several potential causes. First, ensure the monitor is switched on. Second, check if power saving has been activated; press any key or deactivate the screen saver. Third, adjust the brightness control. Fourth, verify that both the monitor and device power cables are properly connected to the devices and grounded mains outlets. Fifth, check that the monitor cable is properly connected to both the device and monitor. Finally, restart the system, press F8 while booting, start in Safe Mode, and set up the monitor as described in your operating system and monitor documentation.
L
Lucas SmithAug 19, 2025
How to fix incorrect time and date on Fujitsu CELSIUS M730?
- L
  Laura HallAug 19, 2025
  If the time and/or date is not correct on your Fujitsu Desktop, it could be due to incorrect settings or a discharged lithium battery. Try setting the correct time and date within your operating system or in the BIOS Setup. If the issue persists, especially after switching on the device, you may need to replace the lithium battery.
Z
Zachary RamosAug 26, 2025
What to do if Fujitsu CELSIUS M730 Desktop cannot be switched off with the ON/OFF switch?
- N
  Nicholas MckinneyAug 27, 2025
  If your Fujitsu Desktop cannot be switched off with the ON/OFF switch, it might be due to a system crash. Keep the on/off switch pressed for at least 4 seconds until the machine switches off. Be aware that this can lead to data loss, as the operating system will not shut down in an orderly way, and error messages may appear upon the next system start.
R
Richard BrewerAug 31, 2025
How to fix no mouse pointer on Fujitsu CELSIUS M730 Desktop?
- D
  Daniel WilliamsSep 1, 2025
  If there is no mouse pointer displayed on the screen of your Fujitsu Desktop, it could be due to an incorrectly connected mouse or a disabled mouse controller. Ensure the mouse cable is properly connected to the system unit. If you're using an adapter or extension lead, check those connections as well. Also, check in the BIOS-Setup to see if the mouse controller is enabled and verify that the mouse driver is properly installed.

Fujitsu CELSIUS M730 Specifications

General

Brand	Fujitsu
Model	CELSIUS M730
Category	Desktop
Language	English

Summary

Your CELSIUS System

Reference Manual Validity

Specifies the CELSIUS models covered by this manual.

Notational Conventions

Important Notes and Safety

Safety Information

Essential safety guidelines for using the device.

Device Cleaning and Maintenance

Instructions for safe and effective cleaning of the device.

Environmental Responsibility

Information on power saving, disposal, and recycling practices.

Regulatory Compliance

Details on CE and FCC compliance statements.

Ports and Operating Elements

CELSIUS M720 Front Panel Overview

Identifies front ports and controls for CELSIUS M720.

CELSIUS M720 Rear Panel Overview

Identifies rear ports and controls for CELSIUS M720.

CELSIUS M730 Front Panel Overview

Identifies front ports and controls for CELSIUS M730.

CELSIUS M730 Rear Panel Overview

Identifies rear ports and controls for CELSIUS M730.

Getting Started with Your System

Unpacking and Delivery Check

Steps to unpack and verify the delivered product.

Initial System Setup Steps

Key steps required for the initial setup of the device.

Connecting External Peripherals

Instructions for connecting external hardware components.

Cable Management

Guidelines for connecting and disconnecting cables safely.

Device Port Identification

Overview of available ports and their symbols.

Monitor Connection Guide

Procedure for connecting a monitor to the system.

Mouse Connection

Steps for connecting USB or PS/2 mice.

Keyboard Connection

Steps for connecting USB or PS/2 keyboards.

USB Device Connectivity

Guide to connecting devices via USB ports.

First Power-On and Software Installation

Initial power-on and software installation process.

Powering On Monitor and Device

Procedure for powering on the monitor and computer.

System Operation

Powering the System On and Off

Procedures for turning the computer on and off.

Device Indicator Lights

Explanation of front panel indicator lights.

Keyboard Usage and Shortcuts

Keyboard layout, important keys, and shortcuts for operation.

BIOS Setup Configuration

Configuring system hardware and functions via BIOS.

Security Features and Data Protection

Security features for device and data protection.

Casing Lock and BIOS Security

Mechanical casing lock and BIOS setup security options.

SmartCard Access Control

Restricting access using SmartCard technology and readers.

Troubleshooting and Tips

Problem Resolution Guidance

Guidance on resolving common issues and seeking support.

Power Issues

Diagnosing and fixing power indicator and switch failures.

Display and Input Problems

Steps to resolve blank monitor and missing mouse pointer issues.

System Time and Error Messages

Correcting time/date and resolving on-screen error messages.

Software Installation and Data Recovery

Guidelines for software installation and restoring hard disk data.

General Usage Tips

General advice and helpful hints for system usage.

System Expansions and Upgrades

Handling Expansion Boards

General information and precautions for handling system boards.

Chassis Access Procedures

Step-by-step guide to opening and closing the computer chassis.

Drive Bay Configuration

Description of drive bay layouts and compatible drive types.

Accessible Drive Installation

Procedures for installing and removing 5.25-inch drives.

Module Reader Installation

Installing/removing 3.5-inch readers like SmartCard or MultiCard.

WLAN Module Installation

Installation and removal of a WLAN module.

Fan Installation and Removal

Procedures for installing/removing front and rear fans.

Hard Disk Drive Installation

Guide to installing hard disk drives, kits, and front panels.

Expansion Board Installation

Procedures for installing and removing expansion boards.

Memory and Processor Upgrades

Instructions for upgrading main memory and replacing the processor.

Heat Sink Management

Handling heat sinks for cooling components during upgrades.

Lithium Battery Replacement

Guide for replacing the system's CMOS lithium battery.

Technical Data

Electrical and Physical Specifications

Electrical data, dimensions, weight, and environmental conditions.

Related product manuals

Fujitsu CELSIUS W5012

51 pages

Fujitsu CELSIUS H5511

80 pages

Fujitsu CELSIUS W570power

89 pages