GE M60 - Page 668

viii M60 MOTOR PROTECTION SYSTEM – INSTRUCTION MANUAL
INDEX
LED test
commands .............................................................................................7-3
FlexLogic operand .........................................................................5-176
settings ...............................................................................................5-118
specifications ..................................................................................... 2-26
LEDs
clear .....................................................................................................5-324
custom labels .................................................................................... 4-44
explained ............................................................................................. 4-40
In Service ............................................................................................. 3-50
settings ...............................................................................................5-120
Trouble .................................................................................................. 3-50
Link power budget ............................................................................. 2-34
Load shedding ....................................................................................5-290
Local access denied message ........................................ 4-62, 5-20
Local access, explained .....................................................................5-8
Local Setting Authorization .........................................................10-14
Lockout from software .................................................................... 5-13
Log in with password ..................................................3-66, 5-9, 5-10
Log in, multiple users cannot ..........................................................2-4
Logic diagram explained ................................................................ 4-62
Logic diagrams, create .................................................................... 4-63
Logic gates, FlexLogic ........................................................4-84, 5-178
Logout users forcefully .......................................................................7-3
Logs, system .......................................................................................... 5-24
Lost password .........................................................................................5-7
M
MAC address
actual values ...................................................................................... 6-29
examples ............................................................................................. 5-43
RxGOOSE .............................................................................................. 5-71
settings for redundancy ............................................................... 5-45
TxGOOSE .............................................................................................. 5-68
Maintenance
actual values ...................................................................................... 6-28
alert to replace battery ....................................................................7-7
battery replacement ....................................................................10-24
cleaning ................................................................................................ 2-38
commands .............................................................................................7-3
module replacement ....................................................................10-23
upgrade or downgrade ...............................................................10-13
Manufacturing date .......................................................................... 6-29
Maximum CT/VT wire size .............................................................. 3-14
Maximum starting rate
logic diagram ...................................................................................5-292
settings ...............................................................................................5-292
Mechanical jam
FlexLogic operands .......................................................................5-170
logic diagram ...................................................................................5-219
settings ...............................................................................................5-218
Memory requirements ..................................................................... 3-52
Menu navigation ................................................................................. 4-51
Message about upgrade over Internet ................................10-14
Messages
clear front panel ............................................................................ 5-324
error ...........................................................................................................7-6
errors and warnings in Engineer ..............................................4-70
Metering
conventions ............................................................................6-12, 6-13
frequency specifications ...............................................................2-28
power specifications .......................................................................2-28
voltage specifications ....................................................................2-28
Metering editor .....................................................................................4-36
Microsoft Windows requirement ...............................................3-52
Mimic diagrams ...................................................................................4-20
MMS connections remaining ........................................................6-11
Modbus
connections remaining ..................................................................6-11
Flex State parameters ................................................................. 5-129
port, close ............................................................................................5-50
register entry ................................................................................... 5-108
settings ..................................................................................................5-50
user map ........................................................................................... 5-108
Modbus Analyzer .................................................................................10-1
Model information, view ..................................................................6-29
Model number ..........................................................................................3-1
Modem connection ............................................................................3-62
Modification file number .................................................................6-29
Modules
add and check settings not defaulted ................................ 10-24
communications ...............................................................................3-30
CT/VT .............................................................................................3-14, 5-6
order codes .........................................................................................2-15
power supply ......................................................................................3-13
replace ............................................................................................... 10-23
transducer I/O ....................................................................................3-28
Monitor
actual values ......................................................................................10-1
devices ..................................................................................................10-1
Monitoring elements settings ................................................... 5-301
Motor
acceleration time settings ........................................................ 5-191
actual values .............................................................................6-4, 6-16
AMP unbalance settings ............................................................ 5-217
curves ................................................................................................. 5-195
FlexAnalogs .............................................................................A-10, A-11
jam ....................................................................................................... 5-218
metering ...............................................................................................6-16
settings ............................................................................................... 5-146
thermal model settings .............................................................. 5-193
Two-speed motor settings ........................................................ 5-221
undercurrent settings ................................................................. 5-220
Motor learned data
actual values ......................................................................................6-24
Motor start supervision
actual values ......................................................................................6-23
specifications .....................................................................................2-24
Motor thermal model
see Thermal model
Mounting ........................................................................................... 3-2, 3-5