HPE ProLiant ML30 Gen10

To Next Page

To Previous Page

2. Install the system board.

3. Open the processor load plate:

a. Push the processor locking lever down to unclip, and then lift it upwards (callout 1).

b. Open the processor load plate (callout 2).

HPE ProLiant ML30 Gen10 Server Maintenance and Service Guide 88

Main Page

Illustrated Parts Catalog7
Mechanical Components7
Flexible Slot Power Supply Blank Spare Part8
EMI Shield Spare Part8
Front Bezel Spare Part8
Air Baffle Spare Part9
Serial Port Blank Spare Part9
System Components9
Flexible Slot Power Supply Spare Part (Hot-Plug)11
Flexible Slot Power Supply Backplane Spare Part11
PCI Fan Spare Part11
DIMM Spare Parts12
System Battery Spare Part12
System Board Assembly Spare Parts12
Processor Spare Parts13
Heatsink Spare Part14
System Fan Spare Part14
Server Options14
HPE Trusted Platform Module 2.0 Spare Part15
Four LFF Hot-Plug Drive Backplane Spare Part16
Eight SFF Hot-Plug Drive Backplane Spare Part16
Miscellaneous System Cable Spare Kit16
Customer Self Repair17
Parts Only Warranty Service17
Réparation Par le Client (CSR)17
Riparazione da Parte del Cliente18
Servizio DI Garanzia Per I Soli Componenti18
Parts-Only Warranty Service (Garantieservice Ausschließlich für Teile)19
Reparaciones del Propio Cliente19
Servicio de Garantía Exclusivo de Componentes20
Reparo Feito Pelo Cliente20
Serviço de Garantia Apenas para Peças21
Removal and Replacement Procedures24
Required Tools24
Safety Considerations25
Electrostatic Discharge25
Symbols on Equipment25
Rack Warnings and Cautions28
Server Warnings and Cautions29
Preparation Procedures29
Power down the Server29
Power up the Server30
Extend the Server from the Rack30
Remove the Server from the Rack31
Slide the Server into the Rack32
Remove the Front Bezel33
Position the Tower Server for Hardware Configuration33
Remove the Access Panel34
Remove the Air Baffle35
Install the Access Panel36
Install the Front Bezel37
Position the Tower Server for Operation37
Removing and Replacing the Front Bezel38
Removing and Replacing the Air Baffle39
Removing and Replacing Drives40
Removing and Replacing an LFF Hot-Plug Drive43
Removing and Replacing an SFF Hot-Plug Drive44
Removing and Replacing Media Devices44
Removing and Replacing a SAS LTO Tape Drive44
Removing and Replacing a USB RDX Drive45
Removing and Replacing an Optical Drive46
Removing and Replacing an Internal USB Device47
Removing and Replacing the Front I/O Assembly49
Removing and Replacing the EMI Shield51
Removing and Replacing the Serial Port Blank52
Removing and Replacing the Four LFF Hot-Plug Drive Backplane53
Removing and Replacing the Eight SFF Hot-Plug Drive Backplane54
Removing and Replacing an M.2 SSD58
Removing and Replacing an Expansion Board59
DIMM-Processor Compatibility61
Removing and Replacing a DIMM62
Removing and Replacing a PCI Fan63
Removing and Replacing the System Fan64
Removing and Replacing a Heatsink67
Replacing a Heatsink68
Removing and Replacing a Processor70
Replacing a Processor73
Removing and Replacing the Non-Hot-Plug Power Supply77
System Battery Replacement82
System Battery Information82
Removing and Replacing the System Battery82
Removing and Replacing the System Board84
Replacing the System Board87
Re-Entering the Server Serial Number and Product ID93
HPE Trusted Platform Module 2.0 Gen10 Option93
NMI Functionality94
Troubleshooting Resources94
Diagnostic Tools94
Product Quickspecs94
Selecting the Boot Mode95
Secure Boot95
Launching the Embedded UEFI Shell96
Intelligent Provisioning96
Intelligent Provisioning Operation97
HPE Insight Remote Support97
HPE Infosight for Servers98
Usb Support98
External USB Functionality98
HPE Smart Storage Administrator98
Component Identification99
Front Panel Components99
Front Panel Leds and Button99
Front Panel LED Power Fault Codes100
Rear Panel Components101
Rear Panel Leds102
System Board Components103
System Maintenance Switch Descriptions104
DIMM Label Identification105
DIMM Slot Locations106
PCI Expansion Slot Definitions107
Drive Leds and Buttons107
Low-Profile LFF Drive LED Definitions108
Drive Bay Numbering109
Fan Numbering111
Fan Mode Behavior112
Media Device Screws112
Cabling Guidelines112
Before Connecting Cables113
Storage Cabling114
LFF Non-Hot-Plug Drive Cabling from the Media Bay114
LFF Non-Hot-Plug Drive Cabling from the Drive Cage116
LFF Hot-Plug Drive Cabling117
SFF Hot-Plug Drive Cabling120
Media Device Cabling124
SATA Optical Drive Cabling124
SAS LTO Tape Drive Cabling125
USB RDX Drive Cabling126
Serial Port Cabling128
System Fan Cabling128
Power Supply Cabling130
Front I/O Cabling131
Front USB Cabling132
Specifications132
Environmental Specifications133
Server Specifications133
Power Supply Specifications133
Support and Other Resources136
Accessing Hewlett Packard Enterprise Support136
Clearcare Technical Support137
Accessing Updates137
Remote Support137
Documentation Feedback138

HPE ProLiant ML30 Gen10

Table of Contents

Other manuals for HPE ProLiant ML30 Gen10

Related product manuals