18 | User Guide Payment terminals
17
8.3 1D and 2D barcode reader
iSMP is equipped with a 1D and 2D barcode reader that can read a number of barcode formats. Consult a
POS partner to ensure how to configure the use of the reader. Please note that the barcode reader will not
work when iSMP is charging.
1D barcode 2D barcode
8.4 How to use the barcode reader
1. Press F4
• Side buttons are active for 20 seconds, the timer is reset after each read
• ”Barcode reader active” is displayed when the reader is active
2. Press one of the side buttons on the terminal to turn on the barcode reader (see previous page).
3. A ”beep” sound will verify that the barcode has been read and sent to the ECR. The laser turns off.
4. To read next barcode, press one of the side buttons again.
5. To abort a barcode reading session, press the red STOP button or MENU. The barcode reading will also be
aborted if a request from the ECR is sent or a payment card is swiped or inserted.
6. Barcode data are sent to the ECR / POS system directly when read. If an error occurs, the barcode must be
read again.
8.5 Supported barcode symbologies
All of these are enabled by default, consult with your POS partner how they are configured from your POS.
8.6 Resetting the barcode reader
If the barcode reader is not working properly, attempt a reset of the barcode reader by following this proce-
dure:
1. Press F to enter main menu.
2. Press 7 Operator menu.
3. Press 6 Barcode reset and the barcode reader will return to default settings.
4. Press OK button to leave the menu or alternatively try again.
MICROPDF EAN-8 EAN-13 UPC-A GS1-128 AZTEC
DATAMATRIX UPC-E EAN-UPC-Addon-2 EAN-UPC-Addon-5 GS1-Databaromni
QR-Code Code-11 Code-39 Code-93 GS1-Databarlimited
Maxi code EAN-128 Code-39-Italian-CPI ITF Intlvd 2 of 5 GS1-Databar expanded
Standard 2 of 5 Matrix 2 of 5 CodaBar MSI ISBT-128
Plessey Telepen CodaBlock A CodaBlock F PDF417
8.3 1D and 2D barcode reader
iSMP4 is equipped with a 1D and 2D barcode reader that can read a number of barcode formats. Consult a POS partner
to ensure how to configure the use of the reader. Please note that the barcode reader will not work when iSMP4 is
charging.
8.4 How to use the barcode reader
1. Press F4
• Side buttons are active for 20 seconds, the timer is reset after each read
• ”Barcode reader active” is displayed when the reader is active
2. Press one of the side buttons on the terminal to turn on the barcode reader (see previous page).
3. A ”beep” sound will verify that the barcode has been read and sent to the ECR. The laser turns off.
4. To read next barcode, press one of the side buttons again.
5. To abort a barcode reading session, press the red STOP button or MENU. The barcode reading will also be aborted
if a request from the ECR is sent or a payment card is swiped or inserted.
6. Barcode data are sent to the ECR / POS system directly when read. If an error occurs, the barcode must be read
again.
By using an API in the terminal, terminal functions can be activated trough the ECR integrated device; tablet or
cash-register. Ex. to activate, to block or to accept bar-code scans.
8.5 Supported barcode symbologies
All of these are enabled by default, consult with your POS partner how they are configured from your POS.
MICROPDF EAN-8 EAN-13 UPC-A GS1-128 AZTEC
DATAMATRIX UPC-E EAN-UPC-Addon-2 EAN-UPC-Addon-5 GS1-Databaromni
QR-Code Code-11 Code-39 Code-93 GS1-Databarlimited
Maxi code EAN-128 Code-39-Italian-
CPI
ITF Intlvd 2 of 5 GS1-Databar
expanded
Standard 2 of 5 Matrix 2 of 5 CodaBar MSI ISBT-128
Plessey Telepen CodaBlock A CodaBlock F PDF417
8.6 Resetting the barcode reader
If the barcode reader is not working properly, attempt a reset of the barcode reader by following this procedure:
1. Press F to enter main menu.
2. Press 7 Operator menu.
3. Press 6 Barcode reset and the barcode reader will return to default settings.
4. Press OK button to leave the menu or alternatively try again.
To Next Page
Loading...
