Advanced Operations
En-73
Operating procedure (➔ page 59)
■ Saturation
*1*2*4
` –50 to 0 to +50
With this setting, you can adjust saturation. “–50” is
the weakest color. “+50” is the strongest color.
■ Color Temperature
*2*4
` Warm
` Normal
` Cool
With this setting, you can adjust the color
temperature.
■ Gamma
*2*4
` –3 to 0 to +3
With this setting, you can adjust the incoming
picture’s R (red), G (green), and B (blue) color signal
in relation to the output color signal.
■ Red Brightness
*2*4
` –50 to 0 to +50
With this setting you can adjust the brightness of red
color. “–50” is the darkest. “+50” is the brightest.
■ Red Contrast
*2*4
` –50 to 0 to +50
With this setting you can adjust the contrast of red
color. “–50” is the least. “+50” is the greatest.
■ Green Brightness
*2*4
` –50 to 0 to +50
With this setting you can adjust the brightness of
green color. “–50” is the darkest. “+50” is the
brightest.
■ Green Contrast
*2*4
` –50 to 0 to +50
With this setting you can adjust the contrast of green
color. “–50” is the least. “+50” is the greatest.
■ Blue Brightness
*2*4
` –50 to 0 to +50
With this setting you can adjust the brightness of blue
color. “–50” is the darkest. “+50” is the brightest.
■ Blue Contrast
*2*4
` –50 to 0 to +50
With this setting you can adjust the contrast of blue
color. “–50” is the least. “+50” is the greatest.
Note
•“Picture Adjust”
cannot be used when:
– The “NET”, “USB” or “BLUETOOTH” input selector is
selected, or
–“Monitor Out” is set to “HDBaseT(TM)”.
*1
This procedure can also be performed on the remote
controller by using the Quick Setup (➔ page 55).
*2
When the “Picture Mode” setting is set to anything other
than “Custom”, this setting cannot be used.
*3
If the “Resolution” setting is set to “4K” (➔ pages 61,
72), this setting is fixed at “Off”.
*4
Press CLR if you want to reset to the default value.
*5
If the “Game Mode” setting is set to “On”, this setting is
fixed at “Off”.
*6
When a 3D video source is input, “Wide Mode” is fixed to
“Full”.
*7
With some TVs, video signals are processed in the same
way as “Through” when this setting is set to “4K”.
*8
When signal is 1080p input at 24 frames per second, it
will be 1080p output at 24 frames per second.
Audio Selector
■ Audio Selector
` ARC:
The audio signal from your TV tuner can be sent
to HDMI OUT of the AV controller.
*1
With this selection, the TV’s audio can be
automatically selected as a priority among other
assignments.
` HDMI:
This can be selected when HDMI IN has been
assigned as an input source. If both HDMI
(HDMI IN) and digital audio inputs (COAXIAL IN
or OPTICAL IN) have been assigned, HDMI
input is automatically selected as a priority.
` COAXIAL:
This can be selected when COAXIAL IN has
been assigned as an input source. If both
coaxial and HDMI inputs have been assigned,
coaxial input is automatically selected as a
priority.
` OPTICAL:
This can be selected when OPTICAL IN has
been assigned as an input source. If both optical
and HDMI inputs have been assigned, optical
input is automatically selected as a priority.
` Analog:
The AV controller always outputs analog signals.
` Balance:
The AV controller always outputs analog signals
from balanced input.
` ---:
The audio signal is not output from the AV
controller.
You can set priorities of audio output when there are
both digital and analog inputs.
Note
• This setting cannot be used with the “NET”, “USB” and
“BLUETOOTH” input selectors.
To Next Page
Loading...
Need help?
General