JUKI SC-922 Engineer's Manual

– 24 –
50 Pedal type Set the type of the pedal. 0/1 U
setting 0 : There is presser foot no movement with the
pedal (KFL)
1 : There is presser foot movement with the
pedal (PFL)
51
Compensation Compensation of starting the solenoid for reverse feed -36 to 36 U 37
of solenoid-on stitching when reverse feed stitching at the start of sewing (10°)
timing of reverse is performed.
feed stitching at
the start of sewing
52 Compensation Compensation of releasing the solenoid for reverse feed -36 to 36 U 37
of solenoid-off stitching when reverse feed stitching at the start of sewing (10°)
timing of reverse is performed.
feed stitching at
the start of sewing
53 Compensation Compensation of releasing the solenoid for reverse feed -36 to 36 U 37
of solenoid-off stitching when reverse feed stitching at the end of sewing (10°)
timing of reverse is performed.
feed stitching at
the end of sewing
54 Motor pulley Effective diameter of pulley to be used for motor 400 to 1400 S
effective is set. (0.1mm)
diameter
55 Foot lift after Function of lifting presser foot at the time of (after) 0/1 U 38
thread trimming thread trimming
0 : Not provided with the function of lifting presser
foot after thread trimming
1 : Provided with the function of lifting presser foot
automatically after thread trimming
56 Reverse Function of reverse revolution to lift the needle at 0/1 U 38
revolution to lift the time of (after) thread trimming
the needle after 0 : Not provided with the function of reverse
thread trimming revolution to lift the needle after thread trimming
1 : Provided with the function of reverse revolution
to lift the needle after thread trimming
58 Function of Function of holding predetermined upper/lower 0 to 3 U 38
holding position of the needle bar
predetermined 0 : Not provided with the function of holding
upper/lower predetermined upper/lower position of the
position of the needle bar
needle bar 1 : Provided with the function of holding predete-
rmined upper/lower of the needle bar
(holding force is medium.)
2 : Provided with the function of holding predete-
rmined upper/ lower position of the needle bar
(holding force is medium.)
3 : Provided with the function of holding predete-
rmined upper/lower position of the needle bar
(holding force is strong.)
59 Function of This function can specify the sewing speed of reverse 0/1 U 38
Auto/Manual feed stitching at the start of sewing.
change/over of 0 : The speed will depend on the manual operation
reverse feed by pedal, etc.
stitching at the 1 : The speed will depend on the specified reverse
start of sewing feed stitching speed (No. 8).
60 Function of stop Function at the time of completion of reverse feed 0/1 U 38
immediately stitching at the start of sewing
after reverse 0 : Not provided with the function of temporary stop
feed stitching of the sewing machine at the time of completion
at the start of of reverse feed stitching at the start of sewing
sewing 1 : Provided with the function of temporary stop
of the sewing machine at the time of completion
of reverse feed stitching at the start of sewing
6
5
1
8
5
0
9
5
1
0
6
0
No. Item Description Setting range Setting level
(Start level ; U : User’s mode, S : Service mode)
0
5
1
1
5
1
1
2
5
3
1
3
5
5
4
5
0
0
9
5
5
1
Indication of
function setting
Ref.
page
∗
∗
∗ Do not change the set values with asterisk (∗) mark as they are functions for maintenance. If the standard set value set at the time
of delivery is changed, it is in danger of causing the machine to be broken or the performance to be deteriorated.

JUKI SC-922 Specifications

General

Brand	JUKI
Model	SC-922
Category	Sewing Machine
Language	English