Keithley 7001

M
Manual triggering 4-36, 4-39, 4-40
Memory 6-3
Menu 4-22
Message exchange protocol 5-36
Messages 4-5
N
Number of scans 4-39
O
Operation condition register 5-9
Operation demo 3-7
Operation details 4-67
Operation event enable register 5-10
Operation event register 5-10
Operation event status 5-8
Operation transition filter 5-9
Optional accessories 1-2
OUTPut subsystem 5-73
Overlapped commands 5-62
P
Power-up sequence 4-2
Primary address selection 5-4
Program messages 5-32
Programming examples 3-22
Power-on defaults 4-24
Q
Questionable event status 5-18
Queues 5-18
R
Read I/O card 4-33
Rear panel 3-1
Recall 4-20
Relay control circuitry 6-5
REN (remote enable) 5-26
Replaceable parts 8-1
Reset 4-24
Reset circuitry 6-3
Response messages 5-35
Restore 4-24
ROUTe subsystem 5-75
:CLOSe 5-76
:STATe 5-77
:CONFigure 5-82
:BBMake 5-82
:CPAir 5-83
:CTYPe 5-84
:POLE 5-85
:SCHannel 5-82
STIMe commands 5-87
:CHannels 5-81
:MEMory 5-88
:RECall 5-88
:SAVE 5-88
:OPEN 5-78
:SCAN 5-79
:POINts 5-80
Routine maintenance 7-3
Run DUT test SYSTem 4-66
S
Save 4-24
Savesetup 4-24
Scan control 4-38
Scan layer 3-11, 4-15
Scan list 4-10, 4-16
Scan spacing 4-38
Scanning channels 4-13
SCPI 3-18
SCPI conformance information F-1
SDC (selective device clear) 5-28
Semi-synchronous trigger link 4-36, 4-59
Sense subsystems 5-91
Sequence condition register 5-13
Sequence event enable register 5-15
Sequence event register 5-14
Sequence event status 5-13
Sequence transition filter 5-13
Serial poll 5-20
Service options 7-1
Service request (SRQ) 5-18, 5-20
Service request enable register 5-20,
5-55, 5-57
Single channel 4-42
Source bypass 4-40, 4-42
SOURce subsystem 5-93
SPE, SPD (serial polling) 5-28
Standard event status 5-7
Standard event status enable register 5-8,
5-40, 5-42
Standard event status register 5-8, 5-43
Status byte 5-18
Status byte register 5-18, 5-58
Status message mode 4-28
Status structure 5-5
STATus subsystem 5-95
CONDition? commands 5-111
ENABle commands 5-100
EVENt? commands 5-96
NTRansition commands 5-109
:PREset 5-112
:PTRansition commands 5-104
:QUEue 5-113
:NEXT 5-113
:ENABle 5-114
:DISable 5-115
Store 4-20
Switching card simulators 3-11
Switching mainframe settings 4-65
Syntax 5-29
SYSTem subsystem 5-117
:POSetup 5-117
:PRESet 5-117
:VERSion? 5-118
:ERRor? 5-119
T
Timer 4-35, 4-38
Trigger condition register 5-15
Trigger control 4-37, 4-42
Trigger event enable register 5-17
Trigger event register 5-17
Trigger event status 5-15
Trigger event transition filter 5-16
Trigger layer 5-24
Trigger link 4-36, 4-39, 4-41, 4-51, 6-11
Trigger model 4-13, 5-21
Trigger subsystem 5-121
:ABORt 5-124
ASYNchronous commands 5-133
COUNt commands 5-125
DELay commands 5-127
DIRection commands 5-132
IMMediate commands 5-124
:INITiate 5-123
:IMMediate 5-123
:CONTinuous 5-123
SIGNal commands 5-132
SOURce commands 5-128
SSYNchronous commands 5-135
TIMer commands 5-130
:TRIGger:COUNt:AUTO 5-126
Troubleshooting 7-14
Type 4-29
U
Use-scanlist-length 4-37
i-2
Artisan Scientific - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisan-scientific.com