How to fix uneven stubble with KUHN FC313RF Air Conditioner?
Uneven stubble can occur due to several reasons. First, check for dull or broken knives and replace them if necessary. Ensure that the knives are installed correctly, with the arrow on the knife's upper face pointing in the disc's direction of rotation. Lastly, verify that the PTO speed is adequate; increase the speed to 1000 min-1 if it's too low.
What to do if KUHN Air Conditioner has bad ground contour adaptation?
If your KUHN Air Conditioner isn't adapting well to the ground contour, there are a few potential causes. Start by adjusting the main frame height with regards to the ground, as an incorrect setting can cause this issue. Also, reduce ground speed if it's excessive. Finally, check the ground pressure and reduce the pressure in the hydro-pneumatic accumulators if it's insufficient.
Why my KUHN FC313RF Air Conditioner makes badly shaped windrows?
Badly shaped windrows can be caused by a too low PTO speed; increase the speed to 1000 min-1. Another cause might be an incorrect swath shield adjustment; in this case you should adjust swath shields.
What to do if soil build up in front of the cutterbar of KUHN FC313RF?
Soil build up in front of the cutterbar can occur if there's too much cutterbar down pressure. Increase the pressure in the hydro-pneumatic accumulators and adjust the main frame height with regards to the ground. Very wet working conditions can also cause this problem.
How to stop considerable vibrations in KUHN FC313RF Air Conditioner?
To address considerable vibrations, adjust roller parallelism using side stop screws.
What to do if the machine transport locks do not engage automatically on KUHN FC313RF?
If the machine transport locks do not engage automatically, the spacer may be distorted. In this case, replace the spacer.
General| Brand | KUHN |
|---|---|
| Model | FC313RF |
| Category | Air Conditioner |
| Language | English |
Visual overview of the machine's front.
Visual overview of the machine's rear.
Details on the machine's identification plate and its importance.
List and description of available optional equipment.
Explains the meaning of warning and informational symbols used.
Comprehensive safety guidelines for operation and maintenance.
Introduction to the importance of safety.
Emphasizes the necessity of reading and adhering to safety.
Pre-operation safety checks for safe machine handling.
Essential safety steps before operating the equipment.
Safety measures for driving the tractor-machine assembly.
Specific safety requirements for public road travel.
Guidelines on maximum permissible speeds.
Safety procedures during the coupling process.
Safety advice for the hydraulic system.
Critical safety instructions for the PTO shaft.
Safety considerations during machine maneuvering.
Safety for remote-operated parts.
Importance and maintenance of safety decals.
Environmental responsibility for waste.
Safety procedures for maintenance and repairs.
Safety measures against projected debris.
General safety rules during machine operation.
Identifies the placement of safety decals on the machine.
Explains the meaning and purpose of each safety decal.
Details on required road lighting and signaling.
French-specific regulations for road use.
Overview of machine parts and key terms.
Detailed technical data and dimensions.
Information regarding noise emissions.
Identification and function of machine controls.
Procedures for attaching and detaching the mower.
Details on the components involved in coupling.
Steps to prepare the tractor for coupling.
Steps to prepare the machine for coupling.
Step-by-step guide for connecting the machine to the tractor.
Instructions for connecting hydraulic lines.
Instructions for connecting electrical systems.
Proper installation of the primary PTO shaft.
Proper installation of the intermediate PTO shaft.
Adjusting frame height and check chains.
Guidance on installing the rear protection cover.
Step-by-step guide for detaching the machine.
Steps to prepare the machine for transport.
Compliance with road and traffic laws.
Steps to prepare the machine for field operation.
Fine-tuning the machine for optimal performance.
How to set the cutting height.
Adjusting ground pressure via hydro-pneumatic accumulators.
Setting the intensity of the conditioning mechanism.
General guidelines for operating the machine in the field.
Recommendations for appropriate drive speeds.
Safety procedures during operation.
Information about the side deflector kit.
Details on the quick release coupler accessory.
Information on mowing unit stop accessories.
Details on the flow limiter accessory.
Maintenance schedule based on usage hours.
Procedures for cleaning the equipment.
Identification of lubrication points.
Specific lubrication for PTO shafts.
General greasing points on the machine.
Oil requirements for various components.
Procedures for changing oil in gearboxes and cutterbar.
Detailed procedures for maintaining the machine.
Maintenance for hydro-pneumatic accumulators.
Adjustment of transport stops for stability.
Verifying roller alignment and spacing.
Adjusting the tension of the drive chain.
Replacing chains and synchronizing rollers.
Checking and adjusting belt tension.
Procedure for replacing drive belts.
How to check the oil level in the cutterbar.
Checking condition of knives and fasteners.
Step-by-step guide for replacing knives.
Procedure for replacing cutting discs.
Inspection of cone covers.
Procedures for storing the machine.
Steps for seasonal storage.
Steps for preparing after storage.
Method for calculating axle loads and weight distribution for safe operation.
To Next Page