2FD/2FF/2FG
2-3-13
Connector Pin No. Signal I/O Voltage Description
1A OFM ENABLE I 0/5 V DC OFM*ENABLE signal
2A OSBSW I 0/5 V DC OSBSW*ON/OFF
3A OFSW I 0/5 V DC OFSW*ON/OFF
4A SET SW I 0/5 V DC OSSW*ON/OFF
5A RESERVE(SW) I
6A RESERVE(SW) I
7A DP SHORT I 0/5 V DC DP* connection signal
8A OSWSW I 0/5 V DC OSWSW*ON/OFF
9A DFSSW2 I 0/5 V DC DFSSW2*ON/OFF
10A DFSSW1 I 0/5 V DC DFSSW1*ON/OFF
11A OSLSW I 0/5 V DC OSLSW*ON/OFF
12A DFTSW I 0/5 V DC DFTSW*ON/OFF
1B OSLED(RED) O 0/5 V DC OSLED* (red) on/off
2B OSLED(GN) O 0/5 V DC OSLED* (green) on/off
3B SBPSOL(RET) O 0/24 V DC SBPSOL* release signal
4B SBPSOL(ACT) O 0/24 V DC SBPSOL* actuate signal
5B OFCL O 0/24 V DC OFCL*ON/OFF
6B EFSSOL O 0/24 V DC EFSSOL*ON/OFF
7B
RESERVE(SOL)
O
8B SBFSSOL O 0/24 V DC SBFSSOL*ON/OFF
9B OFSOL(RET) O 0/24 V DC OFSOL* release signal
10B FOFSOL(ACT) O 0/24 V DC OFSOL* actuate signal
11B OFM ENABLE O 0/5 V DC OFM*ENABLE signal
1 GND - - Ground
2 ODD I DC4.5V (pulse) CCDPCB ODD signal (analog)
3 GND - - Ground
4 EVEN I DC4.5V (pulse) CCDPCB EVEN signal (analog)
5 12V O 12 V DC 12 V DC supply for CCDPCB
6 5.1V O 5.1 V DC 5.1 V DC supply for CCDPCB
7 GND - - Ground
8 CLP O 0/5 V DC (pulse) CCDPCB CLP signal
9 GND - - Ground
10 SHIFT O 0/5 V DC (pulse) CCDPCB SHIFT signal
11 GND - - Ground
12 CLK- O 0/5 V DC (pulse) CCDPCB CLOCK - signal
13 CLK+ O 0/5 V DC (pulse) CCDPCB CLOCK + signal
14 RS+ O 0/5 V DC (pulse) CCDPCB RS + signal
15 RS- O 0/5 V DC (pulse) CCDPCB RS - signal
1 F2 24V O 24 V DC 24 V DC supply for built-in finisher*
2 F2 24V O 24 V DC 24 V DC supply for built-in finisher*
3 GND - - Ground
4 GND - - Ground
5 5V O 5 V DC 5 V DC supply for built-in finisher*
6 GND - - Ground
7 TXD O 0/5 V DC (pulse) Serial signal TXD
8 GND - - Ground
9 RXD I 0/5 V DC (pulse) Serial signal RXD
10 GND - - Ground
11 SET SIG I 0/5 V DC Built-in finisher* connection signal
12 RESET O 0/5 V DC RESET signal
1 JBESW I 0/5 V DC JBESW* ON/OFF
2 5V O 5 V DC 5 V DC supply for JBESW*
3 GND - - Ground
4 GND - - Ground
5 SET SIG I 0/5 V DC Job separator* connection signal
6 GND - - Ground
7 EPDSW I 0/5 V DC EPDSW* ON/OFF
8 5V O 5 V DC 5 V DC supply for EPDSW*
9 LED REM O 0/5 V DC LED(JOB)* on/off
YC33
Connected
to the DP*.
YC34
Connected
to the CCD
PCB.
YC35
Connected
to the built-
in finisher*.
YC36
Connected
to the job
separator*.
*: Optional
To Next Page
Loading...
