Kyocera KM-3035 - Page 318

2FD/2FF/2FG
2-3-14
Connector Pin No. Signal I/O Voltage Description
10 5V O 5 V DC 5 V DC supply for LED(JOB)*
11 FSSOL2 O 0/24 V DC FSSOL(JOB)* release signal
12 FSSOL1 O 0/24 V DC FSSOL(JOB)* actuate signal
13 R24V O 24 V DC 24 V DC supply for FSSOL(JOB)*
1 GND - - Ground
2 SHPSW I 0/5 V DC SHPSW ON/OFF
3 LAMP ON REM O 0/5 V DC EL ON/OFF
4 SM ENABLE O 0/5 V DC SM ENABLE signal
5 SM RET O 0/5 V DC SM RET signal
6 SM CWB O 0/5 V DC SM CWB signal
7 SM CLK O 0/5 V DC (pulse) SM CLOCK signal
8 SM M5 O 0/5 V DC SM drive control signal M5
9 SM M4 O 0/5 V DC SM drive control signal M4
10 SM M3 O 0/5 V DC SM drive control signal M3
11 SM M2 O 0/5 V DC SM drive control signal M2
12 SM M1 O 0/5 V DC SM drive control signal M1
13 SM VREF O 0/5 V DC SM current control voltage Vref
14 ODSW I 0/5 V DC ODSW ON/OFF
15 GND - - Ground
16 OSDS I 0/5 V DC OSDS ON/OFF
17 5V O 5 V DC 5 V DC supply for OSDS
1 DIGLED6 O 0/5 V DC (pulse) OPCB-L DIGLED6 signal
2 DIGLED5 O 0/5 V DC (pulse) OPCB-L DIGLED5 signal
3 DIGLED4 O 0/5 V DC (pulse) OPCB-L DIGLED4 signal
4 DIGLED3 O 0/5 V DC (pulse) OPCB-L DIGLED3 signal
5 DIGLED2 O 0/5 V DC (pulse) OPCB-L DIGLED2 signal
6 DIGLED1 O 0/5 V DC (pulse) OPCB-L DIGLED1 signal
7 SCAN4 O 0/5 V DC (pulse) OPCB-L SCAN4 signal
8 SCAN3 O 0/5 V DC (pulse) OPCB-L SCAN3 signal
9 SCAN2 O 0/5 V DC (pulse) OPCB-L SCAN2 signal
10 SCAN1 O 0/5 V DC (pulse) OPCB-L SCAN1 signal
11 DIGKEY3 I 0/5 V DC OPCB-L DIGKEY3 signal
12 DIGKEY2 I 0/5 V DC OPCB-L DIGKEY2 signal
13 DIGKEY1 I 0/5 V DC OPCB-L DIGKEY1 signal
A1 BUZZER O 0/5 V DC OPCB-L BUZZER signal
A2 X1 I 0/5 V DC (pulse) Touch panel detection voltage X1
A3 Y1 I 0/5 V DC (pulse) Touch panel detection voltage Y1
A4 X2 O 0/5 V DC (pulse) Touch panel detection voltage X2
A5 Y2 O 0/5 V DC (pulse) Touch panel detection voltage Y2
A6 LCD FRAME O 0/5 V DC (pulse) LCD FRAME signal
A7 LCD LOAD O 0/5 V DC (pulse) LCD LOAD signal
A8 LCD CP O 0/5 V DC (pulse) LCD CP signal
A9 LCD VSS(SG) O - LCD VSS signal
A10 LCD VDD(+5V) O 5 V DC LCD VDD signal
A11 LCD VSS(SG) O - LCD VSS signal
A12 LCD DISP OFF O 0/5 V DC LCD DISPLAY signal
A13 LCD D0 O 0/5 V DC (pulse) LCD D0 data
A14 LCD D1 O 0/5 V DC (pulse) LCD D1 data
A15 LCD D2 O 0/5 V DC (pulse) LCD D2 data
A16 LCD D3 O 0/5 V DC (pulse) LCD D3 data
A17 VEE OFF O 0/5 V DC (pulse) LCD VEE signal
B1 P.GND - - Ground
B2 R24V O 24 V DC 24 V DC supply for OPCB-R
B3 LAMP OFF O 0/5 V DC OPCB-R LAMP OFF signal
B4 S.GND - - Ground
B5 5V O 5 V DC 5 V DC supply for OPCB-R
B6 DIGLED8 O 0/5 V DC (pulse) OPCB-R DIGLED8 signal
B7 DIGLED7 O 0/5 V DC (pulse) OPCB-R DIGLED7 signal
B8 SCAN8 O 0/5 V DC (pulse) OPCB-R SCAN8 signal
YC36
Connected
to the job
separator*.
YC37
Connected
to the
scanner
drive PCB
and original
detection
switch.
YC41
Connected
to the left
operation
unit PCB.
YC42
Connected
to the left
and right
operation
unit PCBs.
*: Optional