Lantronix SGX 5150 User Manual

9: Administration
SGX 5150 IoT Device Gateway User Guide 113
TM
System
The SGX 5150 settings allow for reboot, restoring factory defaults, uploading new firmware and
updating a system’s reboot schedule, short name, and long name.
Note: Anytime you reboot the unit, this operation will take some time to complete.
Please wait a minimum of 10-20 seconds after rebooting the unit before attempting to
make any subsequent connections.
Table 9-45 System Settings
System Settings Description
State Select to enable or disable the reboot schedule.
Warning: Use extreme caution when using scheduled reboots. The
SGX 5150 gateway will automatically reboot as scheduled. Any
configuration changes not saved to flash memory will be lost. CLI/WEB
sessions and network traffic will be interrupted. To avoid frequent
reboots, device will not be rebooted if it was started or configured less
than 30 minutes from the current date/time.
Schedule Select the reboot schedule interval: Daily or Interval
Time (24 hour) Set the time to reboot by selecting the Hour and Min (Minute) in the drop-
down menus.
Note: This configuration option appears when the Daily schedule is selected.
Interval Enter the interval number in the field. Then select the type of interval from the
drop-down menu:
 Hours
 Days
 Weeks
 Months
Note: This configuration option appears when the Interval schedule is
selected.
Submit (button) Click the Submit button after settings are made in the above Reboot Schedule
fields.
Reboot Device Click the Reboot button to reboot the SGX 5150 gateway. When rebooted,
your browser should be refreshed and redirected to the main status page after
30 seconds.
Note: The redirect will not work as expected if the IP Address of the SGX
5150 gateway changes after reboot.
Restore Factory Defaults Click the Factory Defaults button to restore the SGX 5150 gateway to the
original factory settings. All configuration will be lost. The SGX 5150 unit
automatically reboots upon setting back to the defaults. After setting the
configuration back to the factory defaults, the gateway will automatically be
rebooted.
Upload New Firmware Click Browse... to browse to and select the firmware file. This process writes
the new firmware file to firmware.rom on the SGX 5150 gateway. The gateway
automatically reboots upon the installation of new firmware. See the section
FTP on page 84.
Caution: Do not to power off or reset the SGX 5150 gateway while
uploading new firmware. Once the upload has completed and the new
firmware has been verified and flashed to memory, the SGX 5150
gateway will automatically be rebooted.

Lantronix SGX 5150 Specifications

General

Certification	FCC ICES-003:2012 RED 2014/53/EU, EMCD 2014/30/EU, EN 300 328 V1.9.1, EN 301 489-1 V1.9.2, EN301 489-17 V2.2.1, EN 301 893 V1.8.1, EN 62311: 2008 AS/NZS CISPR 22, AS/NZS 4268: A1: 2013, AS/NZS 2772.2VCCI EN 55022:2010, EN 55024:2010, EN 61000-3-2:A2 2009, EN 61000-3-3: 2008 UL 60950/CSA 22.2 No. 60950, IEC 60950 CE LVD 2014/35/EU
LED indicators	Yes
Power requirements	9 - 30 VDC
Power over Ethernet (PoE)	No
Power consumption (typical)	1.9 W
Storage temperature (T-T)	-40 - 85 °C
Operating temperature (T-T)	-40 - 70 °C
Operating relative humidity (H-H)	5 - 95 %
Security algorithms	802.1x RADIUS, AES, EAP-FAST, EAP-PEAP, EAP-TLS, EAP-TTLS, FIPS 140-2, MSCHAPv2, TKIP, WPA, WPA2, WPA2-PSK, WPS
Authentication method	RADIUS
Ethernet LAN (RJ-45) ports	1
Supported protocols	IPv4/IPv6, TCP, UDP, ICMP, ARP, Auto-IP, DNS, (S)FTP
Frequency band	2.4 / 5 GHz
Cabling technology	10/100BASE-T(X)
Networking standards	IEEE 802.11a, IEEE 802.11ac, IEEE 802.11b, IEEE 802.11d, IEEE 802.11g, IEEE 802.11h, IEEE 802.11i, IEEE 802.11n, IEEE 802.1x, IEEE 802.3, IEEE 802.3af, IEEE 802.3at, IEEE 802.3u
Ethernet LAN data rates	10, 100 Mbit/s

Weight and Dimensions

Weight	350 g
Dimensions (WxDxH)	110 x 89 x 26 mm