Lantronix SGX 5150 User Manual

6: Network Settings
SGX 5150 IoT Device Gateway User Guide 47
TM
Using XML
 Include in your file: <configgroup name= “interface" instance="eth0">
Link Status and Configuration
Table 6-4 displays the wired link status and configuration information. The view-only status
information is available on the Wired (eth0) Network Ethernet Link page. This same information is
configurable on the Wired (eth0) Network Ethernet Link Configuration page.
Table 6-4 Link (eth0) Configuration
Notes:
 When speed is Auto, duplex must be Auto or Half.
 When speed is not Auto, duplex must be Half or Full.
 Fixed-speed Full duplex produces errors when connected to Auto, due to duplex
mismatch.
To Configure Network Link Settings
Using Web Manager
 To view Ethernet (eth0) link statistics, on the Network page, select Wired Network > Link.
 To configure Ethernet (eth0) link settings, on the Network page, select Wired Network > Link
> Configuration.
Using the CLI
 To enter the command level: enable > config > if 1 > link
Using XML
 Include in your file: <configgroup name= “interface" instance="eth0">
QoS Statistics and Configuration
QoS (Quality of Service) can be enabled and configured for both the Wireless (wlan0) Network
and wired Network (eth0). If enabled, the router will control the flow of outbound traffic according to
the user-defined filters. In other words, QoS improves performance by allowing the user to
prioritize applications. Filters can be defined to prioritize traffic based on the source or destination
network, source or destination port, or the source MAC address. Up to 32 user-defined filters can
be added. The following are predefined priority classes:
Field/Button Description
Speed Select the Ethernet link speed. (Default is Auto.)
 Auto = Auto-negotiation of Link Speed
 10 Mbps = Force 10 Mbps
 100 Mbps = Force 100 Mbps
Duplex Select the Ethernet link duplex mode. (Default is Auto.)
 Auto = Auto-negotiation of Link Duplex
 Half = Force Half Duplex
 Full = Force Full Duplex

Lantronix SGX 5150 Specifications

General

Certification	FCC ICES-003:2012 RED 2014/53/EU, EMCD 2014/30/EU, EN 300 328 V1.9.1, EN 301 489-1 V1.9.2, EN301 489-17 V2.2.1, EN 301 893 V1.8.1, EN 62311: 2008 AS/NZS CISPR 22, AS/NZS 4268: A1: 2013, AS/NZS 2772.2VCCI EN 55022:2010, EN 55024:2010, EN 61000-3-2:A2 2009, EN 61000-3-3: 2008 UL 60950/CSA 22.2 No. 60950, IEC 60950 CE LVD 2014/35/EU
LED indicators	Yes
Power requirements	9 - 30 VDC
Power over Ethernet (PoE)	No
Power consumption (typical)	1.9 W
Storage temperature (T-T)	-40 - 85 °C
Operating temperature (T-T)	-40 - 70 °C
Operating relative humidity (H-H)	5 - 95 %
Security algorithms	802.1x RADIUS, AES, EAP-FAST, EAP-PEAP, EAP-TLS, EAP-TTLS, FIPS 140-2, MSCHAPv2, TKIP, WPA, WPA2, WPA2-PSK, WPS
Authentication method	RADIUS
Ethernet LAN (RJ-45) ports	1
Supported protocols	IPv4/IPv6, TCP, UDP, ICMP, ARP, Auto-IP, DNS, (S)FTP
Frequency band	2.4 / 5 GHz
Cabling technology	10/100BASE-T(X)
Networking standards	IEEE 802.11a, IEEE 802.11ac, IEEE 802.11b, IEEE 802.11d, IEEE 802.11g, IEEE 802.11h, IEEE 802.11i, IEEE 802.11n, IEEE 802.1x, IEEE 802.3, IEEE 802.3af, IEEE 802.3at, IEEE 802.3u
Ethernet LAN data rates	10, 100 Mbit/s

Weight and Dimensions

Weight	350 g
Dimensions (WxDxH)	110 x 89 x 26 mm