Lenze 9300 vector Series - Page 454

Appendix
Index
13
13.2

13.2-1
EDSVF9333V EN 1.0-09/2004
13.2 Index
A
Acceleration, 6.10-1
Acceleration time Tir, additional setpoint of NSET, 8.3-19
Accessories, 12-1
- General, 12.1-1
- Type-specific, 12.2-1
Activating the incremental encoder, 6.7-1
Actual motor current, 8.2-27 , 8.2-50 , 8.3-6 , 9.1-1
Actual motor voltage, 8.2-27 , 8.2-50 , 8.3-6 , 9.1-1
Actual speed value, 8.2-27 , 8.2-50 , 8.3-6 , 9.1-1
Additional setpoint, 8.3-6
Analog input signals, 6.5-4
Analog inputs
- setting input range with jumper X3, 5.9-8
- terminal assignment, 5.9-8
Analog output signals, 6.5-6
Analog outputs
- Configuration, 6.5-6
- terminal assignment, 5.9-8
Application, as directed, 1.2-1
Application as directed, 1.2-1
Application datum, Display, 9.1-1
Auto-TRIP reset, 9.5-1
B
Basic function, 8.3-2
Boost correction, influence of, 6.11-5 , 6.11-10 , 8.3-8
Braking, 6.10-1
C
Cable cross-sections, 3.5-1
Cable type (CAN), 5.10-1
Cables
- for control connections, 5.2-3
- for motor connection, 5.2-1
Calibration, Application datum, 9.1-1
CAN bus identifier, 8.3-23
Capacitance per unit length (CAN), 5.10-1
CE conformity, 1.2-1
CE-typical drive system, 5.4-1 , 5.5-1 , 5.6-1 , 5.7-1
Central supply. Siehe DC-bus connection
Changing parameters, Keypad EMZ9371BC, 7.2-5 , 7.2-7 ,
7.2-8 , 7.2-9 , 7.2-10
Changing the direction of rotation, 6.10-5
Clamp operation, 9.4-2
Code, 7.1-1
Code table, 8.3-1
Cold plate, Requirements of the cooler, 4.1-3 , 4.2-4
Commissioning, 6-1
- before initial switch-on, 6.1-1
- Entry of motor data, 6.6-1
Configuration
- Analog input signals, 6.5-4
- Analog output signals, 6.5-6
- Analog outputs, 6.5-6
- changing the direction of rotation, 6.10-5
- code table, 8.3-1
- controller inhibit (DCTRL1-CINH), 6.4-1
- Current limits, 6.6-12
- Digital input signals, 6.5-1
- Digital output signals, 6.5-3
- Digital outputs, 6.5-3
- Display functions, 9.1-1
- Maximum field frequency, 6.10-1
- Minimum field frequency, 6.10-1
- motor data collection, 6.6-13
- Oscillation damping, 6.11-3
- Quick stop (QSP), 6.10-4
- Relay output, 6.5-3
- Slip compensation, 6.11-1
- switching frequency of inverter, 6.9-1
- table of attributes, 8.5-1
- Umin boost, 6.8-6
Conformity, 1.2-1 , 3.1-1
Control cables, 5.2-3
Control terminals
- changing the assignment of X5, 6.5-1
- changing the assignment of X6, 6.5-1
Control word (AIF), 8.3-13
Controller
- application as directed, 1.2-1
- in clamp operation, 9.4-2
- labelling, 1.2-1
Controller inhibit, drive behaviour, 6.4-1
Current characteristic, current derating, 3.4-1
Current derating, 3.4-1
Current limits, 6.6-12