Appendix
Index
13
13.2
13.2-2
EDSVF9333V EN 1.0-09/2004
D
DC injection braking (GSB)
- automatic, 8.2-43 , 8.2-71
- manual, 8.2-41 , 8.2-69
DC supply, 5.2-1 , 5.4-4 , 5.5-4 , 5.6-4 , 5.7-4
DC-bus connection
- Central supply, 10.2-1
- Decentralised supply, 10.1-1
DC-bus voltage, 8.2-27 , 8.2-50 , 8.3-6 , 9.1-1
Deceleration, 6.10-1
Deceleration time Tif, additional setpoint of NSET, 8.3-19
Decentralised supply. Siehe DC-bus connection
Definition of notes used, 2.4-2
Definitions, Terms, 13.1-1
Degree of pollution, 3.1-1
Derating, 6.6-13 , 6.9-1 , 6.11-3 , 8.2-46 , 8.2-74
device control, 8.3-2
Device protection, 2.3-1
Diagnostics, 7.2-11 , 9.1-1 , 9.1-2
Diameter calculator (DCALC1), 8.2-1
Digital frequency input, connection to X9, 5.12-1
Digital frequency output, connection to X10, 5.12-1
Digital input signals, 6.5-1
Digital inputs, Terminal assignment, 5.9-8
Digital inputs/outputs, Terminal assignment, 11.3-2
Digital output signals, 6.5-3
Digital outputs
- Configuration, 6.5-3
- terminal assignment, 5.9-8
Dimensions,4.1-2,4.1-4,4.2-3,4.2-5,4.3-3,4.4-3
Direction of rotation, inhibiting, 8.2-47 , 8.2-75
Display
- Application datum, 9.1-1
- Operating status, 9.2-1
Display functions, 9.1-1
- Possible values, 9.1-1
Display of operating data, 9.1-1
Display values, 9.1-1
- Calibration, 9.1-1
Drive behaviour
- controller inhibit, 6.4-1
- Influence of the motor cable length, 5.1-3
Drive performance, in case of errors, 9.3-1
E
Electrical installation, system bus (CAN), 5.10-1
EMC, 3.1-2
- what to do in case of interferences, 5.2-6
Emergency-off, controller inhibit, 6.4-1
Enclosure, 3.1-2
Entry of motor data, 6.6-1
Error analysis, 9.2-1
Error elimination, 9.4-1
Error message, Reset, 9.5-1
Error messages, 9.4-5
Explanations, code table, 8.3-1
F
Fault messages, OC3 in clamp operation, 9.4-2
Feedback system, wiring, 5.11-1
Field controller, 6.8-8 , 8.3-8
Field frequency
- maximum, 6.10-1
- Minimum, 6.10-1
Flying restart circuit, 2.3-1
Function blocks, 8.2-1
- diameter calculator (DCALC1), 8.2-1
- internal motor control, vector control (MCTRL2), 8.2-48
- master frequency input (DFIN), 8.2-5
- master frequency output (DFOUT), 8.2-8
- master frequency processing (DFSET), 8.2-18
- master frequency ramp-function generator (DFRFG1),
8.2-13
Fuses, operation with rated power, 400 V (UL), 3.5-2 ,
3.5-3 , 3.5-4
G
General accessories, 12.1-1
General data, 7.2-1
H
History buffer, 9.2-1
- Assembly, 9.2-2
- delete, 9.2-2
Humidity class, 3.1-1
To Next Page
Loading...
