Lenze EPM-T1 Series - Page 526

Index table
15
Appendix
15.1
L
15.1−12
EDSPM−TXXX−9.0−11/2009
Index ImportantPossible settingsName
SelectionLenze
I300A
h
¿
Config
analog/counter
module 10
00000000
h
{1
h
} FFFFFFFF
h
Configuration of analog module,
2/4xcounter module, SSI interface module
or 1xcounter/16xdigital input module on
slot 10
· I300A
h
can only be accessed via Global
Drive Control (GDC). Use I3401
h
in
CoDeSys programming systems.
· I300A
h
is only available for the modular
system.
 12.3−1
 12.4−1
 12.5−1
 12.6−1
1 0
h
2 0
h
3 0
h
4 0
h
I300B
h
¿
Config
analog/counter
module 11
00000000
h
{1
h
} FFFFFFFF
h
Configuration of analog module,
2/4xcounter module, SSI interface module
or 1xcounter/16xdigital input module on
slot 11
· I300B
h
can only be accessed via Global
Drive Control (GDC). Use I3401
h
in
CoDeSys programming systems.
· I300B
h
is only available for the modular
system.
 12.3−1
 12.4−1
 12.5−1
 12.6−1
1 0
h
2 0
h
3 0
h
4 0
h
I300C
h
¿
Config
analog/counter
module 12
00000000
h
{1
h
} FFFFFFFF
h
Configuration of analog module,
2/4xcounter module, SSI interface module
or 1xcounter/16xdigital input module on
slot 12
· I300C
h
can only be accessed via Global
Drive Control (GDC). Use I3401
h
in
CoDeSys programming systems.
· I300C
h
is only available for the modular
system.
 12.3−1
 12.4−1
 12.5−1
 12.6−1
1 0
h
2 0
h
3 0
h
4 0
h
I300D
h
¿
Config
analog/counter
module 13
00000000
h
{1
h
} FFFFFFFF
h
Configuration of analog module,
2/4xcounter module, SSI interface module
or 1xcounter/16xdigital input module on
slot 13
· I300D
h
can only be accessed via Global
Drive Control (GDC). Use I3401
h
in
CoDeSys programming systems.
· I300D
h
is only available for the modular
system.
 12.3−1
 12.4−1
 12.5−1
 12.6−1
1 0
h
2 0
h
3 0
h
4 0
h
I300E
h
¿
Config
analog/counter
module 14
00000000
h
{1
h
} FFFFFFFF
h
Configuration of analog module,
2/4xcounter module, SSI interface module
or 1xcounter/16xdigital input module on
slot 14
· I300E
h
can only be accessed via Global
Drive Control (GDC). Use I3401
h
in
CoDeSys programming systems.
· I300E
h
is only available for the modular
system.
 12.3−1
 12.4−1
 12.5−1
 12.6−1
1 0
h
2 0
h
3 0
h
4 0
h
I300F
h
¿
Config
analog/counter
module 15
00000000
h
{1
h
} FFFFFFFF
h
Configuration of analog module,
2/4xcounter module, SSI interface module
or 1xcounter/16xdigital input module on
slot 15
· I300F
h
can only be accessed via Global
Drive Control (GDC). Use I3401
h
in
CoDeSys programming systems.
· I300F
h
is only available for the modular
system.
 12.3−1
 12.4−1
 12.5−1
 12.6−1
1 0
h
2 0
h
3 0
h
4 0
h