Linksys LGS326P User Manual

11
To view RMON statistics and/or set the refresh rate:
1. Click System Status > RMON > Statistics.
2. Select the Interface for which statistics are to be displayed.
3. Select the Refresh Rate, the time period that passes before the interface statistics are
refreshed.
The statistics are displayed for the selected interface.
•
Bytes Received—Number of octets received, including bad packets and FCS octets, but
excluding framing bits.
•
Drop Events—Number of packets dropped.
•
Packets Received—Number of good packets received, including Multicast and Broadcast
packets.
•
Broadcast Packets Received—Number of good Broadcast packets received. This number
does not include Multicast packets.
•
Multicast Packets Received—Number of good Multicast packets received.
•
CRC & Align Errors—Number of CRC and Align errors that have occurred.
•
Undersize Packets—Number of undersized packets (less than 64 octets) received.
•
Oversize Packets—Number of oversized packets (over 2000 octets) received.
•
Fragments—Number of fragments (packets with less than 64 octets, excluding framing
bits, but including Frame Check Sequence octets) received.
•
Jabbers—Total number received packets that were longer than 1632 octets. This number
excludes frame bits, but includes FCS octets that had either a bad FCS with an integral
number of octets (FCS Error) or a bad FCS with a non-integral octet (Alignment Error)
number. A jabber packet is defined as an Ethernet frame that satisfies the following
criteria:
•
Packet data length is greater than MRU.
•
Packet has an invalid CRC.
•
Received (Rx) Error Event has not been detected.
•
Collisions—Number of collisions received. If Jumbo Frames are enabled, the threshold of
Jabber Frames is raised to the maximum size of Jumbo Frames.
•
Frames of 64 Bytes—Number of frames, containing 64 bytes that were received.
•
Frames of 65 to 127 Bytes—Number of frames, containing 65-127 bytes that were
received.
•
Frames of 128 to 255 Bytes—Number of frames, containing 128-255 bytes that were
received.
•
Frames of 256 to 511 Bytes—Number of frames, containing 256-511 bytes that were
received.

Linksys LGS326P Specifications

General

Switch type	Managed
Switch layer	-
Quality of Service (QoS) support	Yes
Combo SFP ports quantity	2
Installed SFP+ modules quantity	0
Gigabit Ethernet (copper) ports quantity	26
Basic switching RJ-45 Ethernet ports type	Gigabit Ethernet (10/100/1000)
Basic switching RJ-45 Ethernet ports quantity	24
10G support	No
Number of VLANs	128
Networking standards	IEEE 802.1D, IEEE 802.1p, IEEE 802.1Q, IEEE 802.1s, IEEE 802.1w, IEEE 802.1x, IEEE 802.3, IEEE 802.3ab, IEEE 802.3ad, IEEE 802.3af, IEEE 802.3az, IEEE 802.3u, IEEE 802.3x, IEEE 802.3z
Virtual LAN features	Tagged VLAN
Copper ethernet cabling technology	1000BASE-T, 100BASE-T, 10BASE-T
DHCP features	DHCP client
Security algorithms	802.1x RADIUS
Throughput	38.69 Mpps
Jumbo frames	9000
MAC address table	8000 entries
Product color	Black, Blue
LED indicators	Activity, Link, PoE, System
Number of fans	2 fan(s)
Memory type	DRAM
Internal memory	128 MB
Input current	3.5 A
AC input voltage	100 - 240 V
AC input frequency	50 - 60 Hz
Power consumption (typical)	28.58 W
Total Power over Ethernet (PoE) budget	192 W
Storage temperature (T-T)	-40 - 70 °C
Operating temperature (T-T)	0 - 50 °C
Operating relative humidity (H-H)	10 - 90 %

Weight and Dimensions

Depth	200 mm
Width	440 mm
Height	44 mm
Weight	3096 g