EasyManuals Logo

Linksys LGS326P User Manual

Linksys LGS326P
209 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #130 background imageLoading...
Page #130 background image
130
All link local Multicast addresses (FF02::1)
Solicited-Node Multicast address (format FF02::1:FFXX:XXXX)
IPv6 Interface Addresses
To assign an IPv6 address to an IPv6 Interface:
1.
Click Configuration > IP Interface> IPv6 > IPv6 Interface Addresses.
2.
To filter the table, select an interface name, and click Search. The interface appears in the
IPv6 Address Table.
3.
Click Add.
4.
Enter values for the fields.
IPv6 InterfaceDisplays the interface on which the IPv6 address is to be defined.
If an * is displayed, the IPv6 interface is not enabled but has been configured.
IPv6 Address TypeSelect the type of the IPv6 address to add.
Link LocalAn IPv6 address that uniquely identifies hosts on a single network link.
A link local address has a prefix of FE80, is not routable, and can be used for
communication only on the local network. Only one link local address is supported.
If a link local address exists on the interface, this entry replaces the address in the
configuration.
GlobalAn IPv6 address that is a global Unicast IPV6 type that is visible and
reachable from other networks.
IPv6 AddressIn Layer 2, the device supports a singleIPv6 interface. In
addition to the default link local and Multicast addresses, the device also
automatically adds global addresses to the interface based on the router
advertisements it receives. The device supports a maximum of 128 addresses at
the interface. Each address must be a valid IPv6 address that is specified in
hexadecimal format by using 16-bit values separated by colons.

Table of Contents

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Linksys LGS326P and is the answer not in the manual?

Linksys LGS326P Specifications

General IconGeneral
Switch typeManaged
Switch layer-
Quality of Service (QoS) supportYes
Combo SFP ports quantity2
Installed SFP+ modules quantity0
Gigabit Ethernet (copper) ports quantity26
Basic switching RJ-45 Ethernet ports typeGigabit Ethernet (10/100/1000)
Basic switching RJ-45 Ethernet ports quantity24
10G supportNo
Number of VLANs128
Networking standardsIEEE 802.1D, IEEE 802.1p, IEEE 802.1Q, IEEE 802.1s, IEEE 802.1w, IEEE 802.1x, IEEE 802.3, IEEE 802.3ab, IEEE 802.3ad, IEEE 802.3af, IEEE 802.3az, IEEE 802.3u, IEEE 802.3x, IEEE 802.3z
Virtual LAN featuresTagged VLAN
Copper ethernet cabling technology1000BASE-T, 100BASE-T, 10BASE-T
DHCP featuresDHCP client
Security algorithms802.1x RADIUS
Throughput38.69 Mpps
Jumbo frames9000
MAC address table8000 entries
Product colorBlack, Blue
LED indicatorsActivity, Link, PoE, System
Number of fans2 fan(s)
Memory typeDRAM
Internal memory128 MB
Input current3.5 A
AC input voltage100 - 240 V
AC input frequency50 - 60 Hz
Power consumption (typical)28.58 W
Total Power over Ethernet (PoE) budget192 W
Storage temperature (T-T)-40 - 70 °C
Operating temperature (T-T)0 - 50 °C
Operating relative humidity (H-H)10 - 90 %
Weight and Dimensions IconWeight and Dimensions
Depth200 mm
Width440 mm
Height44 mm
Weight3096 g

Related product manuals