LUMINELL SL2 - Page 18

To Next Page

To Previous Page

Page 18 INSTALLATION & USER'S MANUAL SL2

2. Push the dampers tube part thru the mounting holes in the foundation.

3. Mount the dampers rubber part from other side of the foundation.

4. Lower the searchlight on top of dampers and mount bolt washers and nuts as shown in

figure 1.

Main Page

Default Chapter3
- Table of Contents3
Document Revisions and Approvals6
- Document Approvals6
Warnings and Information7
Warranty Conditions Sl28
Maintenance and Service Plan9
Luminell Searchlight System10
- Short System Info10
- External Control Interface11
- Luminell Unity Hub12
Operator Panel, Overview13
Display Symbols and Messages14
- Ebox Alarm Relay15
- Errors that Trigger the Alarm Output15
Installation16
- Lifting the Searchlight16
Cli-30001, Anti Vibration Kit17
Electrical System20
- Electrical Box Mounting Position20
- Electrical Box Installation21
- Cabinet Card22
- SL2 Electrical-Box Overview (24VDC)23
- Selecting/Adjusting the Insulation Monitoring Device, 24VDC Network24
- SL2 Electrical-Box Connection (24VDC)25
  - SL2 Electrical-Box Overview (100-240VAC)26
- SL2 Electrical-Box Connection (100-240VAC)27
  - Operator Panel Connections28
  - External Switch Panel29
- A or B (Activated)29
- Connecting the Switch Panel to the Ebox29
  - Searchlight NMEA Tracking (Optional)30
- NMEA Priority30
  - Ethernet Wiring31
Actions after Installation and Power Failure32
- Automatic Recovery of Stored Searchlight Position in Panel32
- If Panel Position Indicator Differs from the Actual Position of the Searchlight32
  - Synchronize the System33
Starting System34
Joystick Functions35
Light Control36
- Light ON/OFF36
- Spot & Flood Control36
- DIM Adjustment37
Quick Start Menu38
- Fixed Positions38
- Go to Fixed Position38
- Store Fixed Position39
  - Sweep40
- New Sweep40
- Modify Sweep Parameters41
  - Surveillance43
- Setting a New Surveillance Sweep43
- Changing Surveillance Settings45
  - Switch47
  - Synchronized Control48
- Set the Master Control Searchlight On/Off50
- Add and Remove Slaves51
  - Off and Park52
Main Menu53
- Off and Park53
- Switch System53
- Light Position53
- Sweep53
- Surveillance53
- Info53
- Status54
- Settings55
- Backlight Brightness (Adjust the Button´s/ Display Light Intensity)55
- Language55
- Joystick Direction56
- Maximum Rotation Speed57
- Installation57
- Store Origin57
- Store Park Position58
- Name System59
- Start Test Sequence60
- Single Lamp Mode60
- OP Rotation61
- Options Setup63
Cabinet Card Menu System64
- Menu Navigation64
- Down Button64
- Right Button64
- OK Button64
  - Category 1: about65
- (1.1) MAC Address65
- (1.2) IP Address65
- (1.3) Light Model65
- (1.4) SW Version65
  - Category 2: Diagnostics (Support Tool)66
- (2.1) Start66
- (2.2) View Results66
  - Category 3: Usage Stats67
- (3.1) Left Light67
- (3.2) Right Light67
- (3.3) Reset Left67
- (3.4) Reset Right67
  - Category 4: Settings68
- (4.1) Op Wdt68
- (4.2) OP WDT Stats69
- (4.3) OP WDT Reset69
Technical Data70
- SL2 Searchlight70
- SL2 Electrical Box71
- Operator Panel72
- Optional Hardware73
- Optional Software Functions73
- Mechanical Drawings74
- Operator Panel74
- Electrical Box SL2, 100-240VAC75
- Electrical Box SL2, 24VDC76
- Searchlight SL2 (Standard)77
- Searchlight SL2 IR (with Camera)78
Sl2 Searchlight with Thermal Camera79
- Thermal Camera Introduction79
- SL2IR Additional Specifications80
Sl2Ir - Video Connection82
Set Camera Video Format Standard83
- Menu Navigation83
- Down Button83
- Right Button83
- OK Button83
  - Factory Setup, How to Change between PAL and NTSC84
Using the Thermal Camera in Cam Mode85
- Activate the Thermal Camera85
- Camera Tilt87
- Tilt up87
- Tilt down88
  - Spot Meter89
Menu - Camera Settings90
- Palette91
- Zoom92
Support93

LUMINELL SL2 - Page 18

Table of Contents

Related product manuals