LUMINELL SL2 - Page 62

96 pages

Save Page as PDF

To Next Page

To Next Page

To Previous Page

To Previous Page

Loading...

Page 62 INSTALLATION & USER'S MANUAL SL2

OP Rotation illustration.

270º

0º

90º

180º

Table of Contents

Default Chapter3
- Table of Contents3
Document Revisions and Approvals6
- Document Approvals6
Warnings and Information7
Warranty Conditions Sl28
Maintenance and Service Plan9
Luminell Searchlight System10
- Short System Info10
- External Control Interface11
- Luminell Unity Hub12
Operator Panel, Overview13
Display Symbols and Messages14
- Ebox Alarm Relay15
- Errors that Trigger the Alarm Output15
Installation16
- Lifting the Searchlight16
Cli-30001, Anti Vibration Kit17
Electrical System20
- Electrical Box Mounting Position20
- Electrical Box Installation21
- Cabinet Card22
- SL2 Electrical-Box Overview (24VDC)23
- Selecting/Adjusting the Insulation Monitoring Device, 24VDC Network24
- SL2 Electrical-Box Connection (24VDC)25
  - SL2 Electrical-Box Overview (100-240VAC)26
- SL2 Electrical-Box Connection (100-240VAC)27
  - Operator Panel Connections28
  - External Switch Panel29
- A or B (Activated)29
- Connecting the Switch Panel to the Ebox29
  - Searchlight NMEA Tracking (Optional)30
- NMEA Priority30
  - Ethernet Wiring31
Actions after Installation and Power Failure32
- Automatic Recovery of Stored Searchlight Position in Panel32
- If Panel Position Indicator Differs from the Actual Position of the Searchlight32
  - Synchronize the System33
Starting System34
Joystick Functions35
Light Control36
- Light ON/OFF36
- Spot & Flood Control36
- DIM Adjustment37
Quick Start Menu38
- Fixed Positions38
- Go to Fixed Position38
- Store Fixed Position39
  - Sweep40
- New Sweep40
- Modify Sweep Parameters41
  - Surveillance43
- Setting a New Surveillance Sweep43
- Changing Surveillance Settings45
  - Switch47
  - Synchronized Control48
- Set the Master Control Searchlight On/Off50
- Add and Remove Slaves51
  - Off and Park52
Main Menu53
- Off and Park53
- Switch System53
- Light Position53
- Sweep53
- Surveillance53
- Info53
- Status54
- Settings55
- Backlight Brightness (Adjust the Button´s/ Display Light Intensity)55
- Language55
- Joystick Direction56
- Maximum Rotation Speed57
- Installation57
- Store Origin57
- Store Park Position58
- Name System59
- Start Test Sequence60
- Single Lamp Mode60
- OP Rotation61
- Options Setup63
Cabinet Card Menu System64
- Menu Navigation64
- Down Button64
- Right Button64
- OK Button64
  - Category 1: about65
- (1.1) MAC Address65
- (1.2) IP Address65
- (1.3) Light Model65
- (1.4) SW Version65
  - Category 2: Diagnostics (Support Tool)66
- (2.1) Start66
- (2.2) View Results66
  - Category 3: Usage Stats67
- (3.1) Left Light67
- (3.2) Right Light67
- (3.3) Reset Left67
- (3.4) Reset Right67
  - Category 4: Settings68
- (4.1) Op Wdt68
- (4.2) OP WDT Stats69
- (4.3) OP WDT Reset69
Technical Data70
- SL2 Searchlight70
- SL2 Electrical Box71
- Operator Panel72
- Optional Hardware73
- Optional Software Functions73
- Mechanical Drawings74
- Operator Panel74
- Electrical Box SL2, 100-240VAC75
- Electrical Box SL2, 24VDC76
- Searchlight SL2 (Standard)77
- Searchlight SL2 IR (with Camera)78
Sl2 Searchlight with Thermal Camera79
- Thermal Camera Introduction79
- SL2IR Additional Specifications80
Sl2Ir - Video Connection82
Set Camera Video Format Standard83
- Menu Navigation83
- Down Button83
- Right Button83
- OK Button83
  - Factory Setup, How to Change between PAL and NTSC84
Using the Thermal Camera in Cam Mode85
- Activate the Thermal Camera85
- Camera Tilt87
- Tilt up87
- Tilt down88
  - Spot Meter89
Menu - Camera Settings90
- Palette91
- Zoom92
Support93

Related product manuals

Preview: LUMINELL SL1

LUMINELL RLX CxZ1.21