Magnetek FLEX BASE User Manual

Page 43
001 : On & Off pushbutton pair (for keypad type 01, 02 and 03).
002 : Magnet On & Off pushbutton pair (for keypad type 01, 02 and 03).
003 : On + Start & Off + Start pushbutton pair (for keypad type 03 only).
7.9 Program Pushbutton Output Relay 2 (PB3/PB4) (RX)
1) Make sure the programming cable is connected to the system.
2) Press “→” button to enter Function 2 setting.
3) Press “↑” and “↓” button to change system channel as a whole or…
4) Press “→” button to go to the digit on the far left.
5) Press “↑” and “↓” button to change numeric value.
6) Press “→” button to go to the next digit to the right and repeat step 5
7) Press BACK button to go back to step 3 or 4.
8) Exit Program System Channel by pressing the “BACK” button until the
cursor is shown next to “PB RLY2”.
9) Press “↑” and “↓” button to scroll through other Flex Mini settings.
001 : On & Off pushbutton pair (for keypad type 01, 02 and 03).
002 : Magnet On & Off pushbutton pair (for keypad type 01, 02 and 03).
003 : On + Start & Off + Start pushbutton pair (for keypad type 03 only).
7.10 Program Pushbutton Output Relay 3 (PB5/PB6) (RX)
1) Make sure the programming cable is connected to the system.
2) Press “→” button to enter Function 3 setting.
3) Press “↑” and “↓” button to change system channel as a whole or…
4) Press “→” button to go to the digit on the far left.
5) Press “↑” and “↓” button to change numeric value.
6) Press “→” button to go to the next digit to the right and repeat step 5
7) Press BACK button to go back to step 3 or 4.
8) Exit Program System Channel by pressing the “BACK” button until the
cursor is shown next to “PB RLY3”.
9) Press “↑” and “↓” button to scroll through other Flex Mini settings.
001 : On & Off pushbutton pair (for keypad type 01, 02 and 03).
002 : Magnet On & Off pushbutton pair (for keypad type 01, 02 and 03).
003 : On + Start & Off + Start pushbutton pair (for keypad type 03 only).
7.11 Program Pushbutton Output Relay 4 (PB7/PB8) (RX)
1) Make sure the programming cable is connected to the system.
2) Press “→” button to enter Function 4 setting.
3) Press “↑” and “↓” button to change system channel as a whole or…
4) Press “→” button to go to the digit on the far left.
5) Press “↑” and “↓” button to change numeric value.
6) Press “→” button to go to the next digit to the right and repeat step 5
7) Press BACK button to go back to step 3 or 4.
8) Exit Program System Channel by pressing the “BACK” button until the
cursor is shown next to “PB RLY4”.
9) Press “↑” and “↓” button to scroll through other Flex Mini settings.
001 : On & Off pushbutton pair (for keypad type 01, 02 and 03).
002 : Magnet On & Off pushbutton pair (for keypad type 01, 02 and 03).
003 : On + Start & Off + Start pushbutton pair (for keypad type 03 only).

Magnetek FLEX BASE Specifications

General

Brand	Magnetek
Model	FLEX BASE
Category	Controller
Language	English