EasyManua.ls Logo

Martin MAC 2000 Performance - Service Manual

Martin MAC 2000 Performance
34 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
MAC 2000
Performance
service manual

Table of Contents

Other manuals for Martin MAC 2000 Performance

Preview: User Manual
User Manual45 pages

Questions and Answers

  • M
    Melissa EscobarAug 1, 2025
    What to do if my Martin MAC 2000 Performance Lighting Equipment has no light and displays a 'LERR' error message?
    • F
      fryeerinAug 1, 2025
      If your Martin Lighting Equipment shows a 'LERR' message and there is no light, the issue may be due to several reasons. First, ensure that the transformer settings match your local AC voltage and frequency by disconnecting the fixture and checking the settings. Also, the lamp might be blown, not installed, or too hot to ignite, so disconnect the fixture and replace the lamp if needed, install the lamp if it is not installed, or allow the lamp to cool for 5-10 minutes before trying again. Finally, check that the lamp access plate is fully seated and locked, as an open safety switch will prevent the lamp from working.
  • C
    Carolyn ClarkAug 5, 2025
    How to fix Martin MAC 2000 Performance that is completely dead?
    • W
      Wayne JonesAug 5, 2025
      If your Martin Lighting Equipment is completely dead, start by checking that the power is switched on and all cables are securely plugged in. If the issue persists, the primary fuse located near the mains inlet might be blown; disconnect the fixture and replace the fuse. Additionally, check the secondary fuses located on the PCB inside the base and replace them if necessary.
  • P
    Patricia MerrittAug 11, 2025
    Why does my Martin Lighting Equipment lamp cut out intermittently?
    • R
      Randall DixonAug 11, 2025
      If the lamp in your Martin Lighting Equipment cuts out intermittently, it could be due to the fixture overheating. Allow the fixture to cool down, clean the air filters, and reduce the ambient room temperature. Also, verify that the transformer settings match your local AC voltage and frequency by disconnecting the fixture and checking the settings.
  • K
    Kathleen MatthewsAug 15, 2025
    What to do if Martin Lighting Equipment fixtures reset but respond erratically to the controller?
    • S
      Sara MortonAug 15, 2025
      If your Martin Lighting Equipment fixtures reset correctly but respond erratically or not at all to the controller, there might be a bad data link. Inspect the connections and cables, fix any poor connections, and repair or replace damaged cables. Ensure the data link is terminated by inserting a termination plug in the output jack of the last fixture on the link. Check that the fixtures are correctly addressed and the protocol settings are correct. Try bypassing one fixture at a time until normal operation is regained by unplugging the XLR in and out connectors and connecting them directly together. If the XLR pin-out on fixtures does not match (pins 2 and 3 reversed), install a phase-reversing cable between the fixtures or swap pins 2 and 3 in the fixture that behaves erratically.
  • K
    Kevin PrattAug 20, 2025
    Why does the mechanical effect on my Martin Lighting Equipment lose position?
    • M
      Michael KnightAug 20, 2025
      If the mechanical effect on your Martin Lighting Equipment loses position, it may be that the transformer setting does not match local voltage. Disconnect the fixture and check the transformer setting, correcting it if necessary. For issues related to cleaning, adjustment, or lubrication of the mechanical train, contact a Martin technician for service.
  • C
    Christina KellerAug 26, 2025
    How to troubleshoot wandering magnetically indexed effects on Martin MAC 2000 Performance Lighting Equipment?
    • M
      Mary McneilAug 26, 2025
      If the magnetically indexed effect on your Martin Lighting Equipment resets correctly but wanders after the fixture reaches operating temperature, disable effects feedback. Contact a Martin technician for service.

Summary

INTRODUCTION

PRECAUTIONS

Lists critical safety warnings for electrical shock, UV radiation, and electrostatic discharge.

FRAMING SHUTTERS

REPLACE MOTOR

Guide for replacing the motor within the framing shutters assembly.

ADJUST MOTOR

FRAMING ROTATION

REPLACE MOTOR OR GEAR

Instructions for replacing the motor or gear responsible for framing rotation.

IRIS

REPLACE IRIS

Detailed steps for removing and installing the iris assembly.

GOBO ANIMATION WHEEL

REPLACE POSITION BELT

REPLACE POSITION MOTOR

Guide for replacing the motor that controls the gobo animation wheel position.

GOBO WHEEL

REPLACE ROTATION MOTOR, ROTATION GEAR, AND BELT

Comprehensive guide for replacing the motor, gear, and belt of the gobo wheel.

REPLACE GOBO WHEEL MOTOR

Steps for replacing the motor specifically for the gobo wheel rotation.

ZOOM; FOCUS MODULE

REMOVE ZOOM; FOCUS MODULE

INSTALL ZOOM; FOCUS MODULE

ZOOM AND FOCUS

REPLACE MOTORS

Procedures for replacing zoom and focus motors.

REPLACE ZOOM LENS

REPLACE FOCUS LENS

ADJUST ZOOM RESET SWITCH ACTIVATOR

Procedure to adjust the zoom reset switch activator for zoom errors.

ADJUST FOCUS RESET SWITCH ACTIVATOR

Procedure to adjust the focus reset switch activator for focus errors.

EFFECT WHEEL

REMOVE EFFECT WHEEL MODULE

INSTALL EFFECT WHEEL MODULE

REPLACE EFFECT WHEEL MOTOR

Guide for replacing the motor connected to the effect wheel.

REPLACE EFFECT WHEEL

ADJUST EFFECT WHEEL

Martin MAC 2000 Performance Specifications

General IconGeneral
BrandMartin
ModelMAC 2000 Performance
CategoryLighting Equipment
LanguageEnglish

Related product manuals