Maxsys PC4020 - Page 72

To Next Page

To Previous Page

Listing Requirements

A.6 Sensor Reset for 4-Wire Smoke Detectors

SAUX Connection PC4204/PC4204CXCF Connection

A.7 PGM Connections

A.8 AMS-220 Addressable Smoke Detector Connection

NOTE: Maximum of 128 devices (for software version 3.3 and

higher)

Main Page

Default Chapter4
- Table of Contents4
Section 1: Introduction6
- Out of the Box6
- Specifications and Features6
Section 2: Installation and Wiring7
- Planning the System7
- Terminal Descriptions7
- Wire Routing for Power and Non-Power Limited7
- Current Ratings - Alarm Control Panel and Modules7
- Combus Operation and Wiring8
- Zone Wiring9
- Specialized Zone Wiring9
- Programmable Output Wiring10
- AML Device Wiring10
- Wiring Powered Devices (AUX, SAUX+)11
- Telephone Line Wiring11
- Bell Output Wiring (BELL and BELL )12
- Earth Ground Wiring12
- Applying Power (AC and Battery)12
- Lithium Batteries13
Section 3: How to Program14
- Introduction to Programming14
- Programming by Reference Number14
- Programming Decimal Data14
- Programming Hexadecimal Data15
- Programming Toggle Options15
Section 4: Module Enrollment16
- Enrolling Keypads and Modules16
- Deleting Modules16
- Confirming Modules16
- Enrolling AML Devices17
Section 5: Partitions and Zones18
- Zone Supervision18
- Creating Partitions18
- Adding Zones to Partitions19
- Zone Programming19
- Bypass Grouping22
Section 6: Keypad Operation24
- Partition Keypads24
- Global Keypads24
- Keypad Toggle Options24
- Keypad Time-Out25
- Keypad Blanking25
- Fire, Auxiliary and Panic Keys25
- Keypad Lockout25
- Keypad Tampers26
- Alarm Memory Display26
- Zone Bypass Display26
- Function Key Programming26
Section 7: Installer and Access Codes28
- Installer's Code28
- Installer-Programmed Access Codes28
- Programming Access Codes28
- Modify an Existing Code30
- Change User Code Options30
- Delete an Existing Code30
- Special Codes31
- Guard Code31
- Access Code Options31
- Access Levels32
Section 8: Arming and Disarming33
- Arming and Disarming Options33
- Automatic Arming33
- Close Time Timer (CTT Duration)33
- Disarm Delay33
- Dual Users for Disarming34
Section 9: Entry and Exit Delay35
- Entry and Exit Delay Times35
- Entry and Exit Delay Options35
Section 10: System Programming36
- AC/DC Power Options36
- Bell Circuit Supervision36
- Clock Options36
- Event Messages36
- Swinger Shutdown37
- Tampers37
- Telephone Line Supervision37
- Test Transmissions37
- Transmission Delay38
- Cross Zone (Police Code) Alarm38
- System Label38
- Hourly Print38
Section 11: Programmable Outputs39
- Main Panel Outputs39
- Programming Output Options for Modules39
- Programmable Output Options39
- Output Pulse Times42
Section 12: Communications Programming43
- Telephone Numbers43
- Account Numbers43
- Dialing Parameters43
- Communicator Toggle Options43
- Dialer Direction44
- Communicator Formats44
- Reporting Codes46
Section 13: Downloading47
- Downloading Options47
- Periodic Call-Up47
- PC-Link47
Section 14: Event Scheduling48
- Date Schedules48
- Holiday Groups48
- Open/Close Suppression48
- Arming/Disarming Schedules49
- Scheduled AMS-220/220T Smoke Detector Test49
- CTT Schedule49
- Seismic Schedule49
Section 15: LINKS Communications50
- LINKS1000 (Cellular Communications)50
- LINKS2XXX (Long-Range Radio Communications)50
- T-Link TCP/IP Communications)50
Section 16: Diagnostics and Troubleshooting51
- General Diagnostics51
- Restoring Factory Default Programming51
- Hardware Reset51
- Viewing Trouble Conditions51
- System Fault Squawk52
Section 17: Local, Central & Remote Station Fire Installation54
Instructions54
- Introduction54
- Hardware Description and Specifications54
Section 18: Fire Zone Types56
- Partitions and Fire System Configuration56
- Standard Fire Zone56
- Delayed Fire Zone56
- Auto Verify Fire57
- Waterflow Zone57
- Fire Supervisory Zone58
- PC4701 Zones58
- 4-Wire Smoke Detector Zones58
- Addressable Smoke Detector Zones58
- Addressable Fire Point Module58
Section 19: PC4702BP Output Programming59
- Alarm Notification Output Types59
- Programming PC4702BP Outputs59
- Fire Bell Options59
- Partitions and Fire System Configuration59
Section 20: Fire System Operation61
- Manual Signal Silence61
- Automatic Signal Silence (Bell Cut-Off)61
- Signal Silence Inhibit Timer (Fire Silence Delay)61
- Fire System Reset61
- Manual Sensor Reset ([*][7][2])61
- Subsequent Alarm Operation61
- Fire Silence/Reset User Codes62
- Auto-Scroll LCD Keypad Display62
- Fire Trouble Conditions62
- AC Delays63
- Bypassing Fire Zones63
- Fire Drill Feature63
- Fire Inspector Test63
- Testing AMS-220/220T Smoke Detectors63
- Lamp Test64
- PC4701 Remote Station Alarm/Trouble Relays64
- Fire Reporting Codes64
- Upload/Download Considerations65
Section 21: Listing Requirements66
- UL Listed Commercial Burglary and Residential Burglary Installations66
- Commercial Fire Alarm Installations66
- ULC Listing Requirements67
Appendix A: Wiring Diagrams68
Appendix B: Reporting Codes74
Appendix C: Zone Reporting Codes77
ASCII Characters78

Maxsys PC4020 - Page 72

Table of Contents

Other manuals for Maxsys PC4020