i
Table of Contents
Section 1: Introduction 1
1.1 Out Of The Box ............................................................................ 1
1.2 Specifications and Features .......................................................... 1
Section 2: Installation and Wiring 2
2.1 Planning the System ..................................................................... 2
2.2 Terminal Descriptions .................................................................. 2
2.3 Wire Routing for Power and Non-Power Limited ....................... 2
2.4 Current Ratings – Alarm Control Panel and Modules ................. 2
2.5 Combus Operation and Wiring .................................................... 3
2.6 Zone Wiring ................................................................................. 4
2.7 Specialized Zone Wiring .............................................................. 4
2.8 Programmable Output Wiring ...................................................... 5
2.9 AML Device Wiring .................................................................... 5
2.10 Wiring Powered Devices (AUX, SAUX+) .................................. 6
2.11 Telephone Line Wiring ................................................................ 6
2.12 Bell Output Wiring (BELL+ and BELL-) ................................... 7
2.13 Earth Ground Wiring ................................................................... 7
2.14 Applying Power (AC and Battery) ............................................... 7
2.15 Lithium Batteries .......................................................................... 8
Section 3: How to Program 9
3.1 Introduction to Programming ....................................................... 9
3.2 Programming by Reference Number ........................................... 9
3.3 Programming Decimal Data ......................................................... 9
3.4 Programming Hexadecimal Data ............................................... 10
3.5 Programming Toggle Options .................................................... 10
Section 4: Module Enrollment 11
4.1 Enrolling Keypads and Modules ................................................ 11
4.2 Deleting Modules ....................................................................... 11
4.3 Confirming Modules .................................................................. 11
4.4 Enrolling AML Devices ............................................................. 12
Section 5: Partitions and Zones 13
5.1 Zone Supervision ....................................................................... 13
5.2 Creating Partitions ...................................................................... 13
5.3 Adding Zones to Partitions ........................................................ 14
5.4 Zone Programming .................................................................... 14
5.5 Bypass Grouping ........................................................................ 17
Section 6: Keypad Operation 19
6.1 Partition Keypads ....................................................................... 19
6.2 Global Keypads .......................................................................... 19
6.3 Keypad Toggle Options ............................................................. 19
6.4 Keypad Time-out ....................................................................... 20
6.5 Keypad Blanking ........................................................................ 20
6.6 Fire, Auxiliary and Panic Keys .................................................. 20
6.7 Keypad Lockout ......................................................................... 20
6.8 Keypad Tampers ........................................................................ 21
6.9 Alarm Memory Display ............................................................. 21
6.10 Zone Bypass Display ................................................................. 21
6.11 Function Key Programming ....................................................... 21
Section 7: Installer and Access Codes 23
7.1 Installer’s Code .......................................................................... 23
7.2 Installer-Programmed Access Codes ......................................... 23
7.3 Programming Access Codes ...................................................... 23
7.4 Modify An Existing Code .......................................................... 25
7.5 Change User Code Options ........................................................ 25
7.6 Delete An Existing Code ............................................................ 25
7.7 Special Codes ............................................................................. 26
7.8 Guard Code ................................................................................ 26
7.9 Access Code Options ................................................................. 26
7.10 Access Levels ............................................................................. 27
Section 8: Arming and Disarming 28
8.1 Arming and Disarming Options ................................................. 28
8.2 Automatic Arming ..................................................................... 28
8.3 Close Time Timer (CTT Duration) ............................................ 28
8.4 Disarm Delay ............................................................................. 28
8.5 Dual Users For Disarming ......................................................... 29
Section 9: Entry and Exit Delay 30
9.1 Entry and Exit Delay Times ....................................................... 30
9.2 Entry and Exit Delay Options .................................................... 30
Section 10: System Programming 31
10.1 AC/DC Power Options ............................................................... 31
10.2 Bell Circuit Supervision ............................................................. 31
10.3 Clock Options ............................................................................ 31
10.4 Event Messages .......................................................................... 31
10.5 Swinger Shutdown ..................................................................... 32
10.6 Tampers ...................................................................................... 32
10.7 Telephone Line Supervision ...................................................... 32
10.8 Test Transmissions ..................................................................... 32
10.9 Transmission Delay .................................................................... 33
10.10 Cross Zone (Police Code) Alarm .............................................. 33
10.11 System Label ............................................................................. 33
10.12 Hourly Print ............................................................................... 33
Section 11: Programmable Outputs 34
11.1 Main Panel Outputs .................................................................... 34
11.2 Programming Output Options for Modules ............................... 34
11.3 Programmable Output Options .................................................. 34
11.4 Output Pulse Times .................................................................... 37
Section 12: Communications Programming 38
12.1 Telephone Numbers ................................................................... 38
12.2 Account Numbers ...................................................................... 38
12.3 Dialing Parameters ..................................................................... 38
12.4 Communicator Toggle Options .................................................. 38
12.5 Dialer Direction .......................................................................... 40
12.6 Communicator Formats .............................................................. 40
12.7 Reporting Codes ......................................................................... 41
Section 13: Downloading 42
13.1 Downloading Options ................................................................ 42
13.2 Periodic Call-up ......................................................................... 42
13.3 PC-Link ...................................................................................... 42
Section 14: Event Scheduling 43
14.1 Date Schedules ........................................................................... 43
14.2 Holiday Groups .......................................................................... 43
14.3 Open/Close Suppression ............................................................ 43
14.4 Arming/Disarming Schedules .................................................... 44
14.5 Scheduled AMS-220/220T Smoke Detector Test ...................... 44
14.6 CTT Schedule ............................................................................ 44
14.7 Seismic Schedule ....................................................................... 44
Section 15: LINKS Communications 45
15.1 LINKS1000 (Cellular Communications) ................................... 45
15.2 LINKS2XXX (Long-range Radio Communications) ................ 45
15.3 T-Link TCP/IP Communications) .............................................. 45
To Next Page
Loading...
