34
■ Model name
The model name can be set or altered in the Model Set-
up, Setup Tools menu.
■ Save/Load Setup les
You may save the settings of any VBar connected to a
le on your VBar Control transmitter. The saved le can
serve as a backup, for reverting to earlier or different
settings, or for transferring settings from one VBar to the
next. The saved le can be copied to your PC using the
USB connection for an additional backup or to share it
with our service staff.
ACE DS0606 333 Hz 1.500 µSec
ACE DS0606 n 333 Hz 760 µSec
Airtronics 94758 333 Hz 1.500 µSec
Airtronics 94761 333 Hz 1.500 µSec
Align DS 520 333 Hz 1.500 µSec
Align DS 525 M 333 Hz 1.500 µSec
Align DS 620 333 Hz 1.500 µSec
Align DS 650 333 Hz 1.500 µSec
Align DS 651 333 Hz 1.500 µSec
Futaba S 9253 333 Hz 1.500 µSec
Futaba S 9254 333 Hz 1.500 µSec
Futaba S 9257 333 Hz 1.500 µSec
Futaba S 9451 333 Hz 1.500 µSec
Futaba S 9650 333 Hz 1.500 µSec
Futaba S 3153 333 Hz 1.500 µSec
Futaba S 3154 333 Hz 1.500 µSec
Futaba BLS 451 333 Hz 1.500 µSec
Futaba S 9251 333 Hz 760 µSec
Futaba S 9256 333 Hz 760 µSec
Futaba BLS 251 333 Hz 760 µSec
Futaba BLS 256 HV 333 Hz 760 µSec
Futaba BLS 257 333 Hz 1.500 µSec
Graupner HBS 770 333 Hz 1.500 µSec
Hitec 5925 MG 333 Hz 1.500 µSec
Hitec 6965 HB 333 Hz 1.500 µSec
Hitec HSG-5083MG 333 Hz 1.000 µSec
JR 8900 G 333 Hz 1.500 µSec
JR 3400G 333 Hz 1.500 µSec
JR 2700 G 200 Hz 1.500 µSec
JR 8700 G 200 Hz 1.500 µSec
JR 810 G 200 Hz 1.500 µSec
JR MP 80 G 333 Hz 1.500 µSec
JR SPG 01 333 Hz 1.500 µSec
JR MP 83 GWV 333 Hz 1.500 µSec
Logictech 2100 G 333 Hz 1.500 µSec
Logictech 6100 G 333 Hz 1.000 µSec
MKS HBL 950 HV 333 Hz 1.500 µSec
MKS HBL 980 HV 333 Hz 760 µSec
MKS HBL 669 333 Hz 760 µSec
MKS BLS 980 333 Hz 760 µSec
MKS BLS 990 333 Hz 760 µSec
MKS DS 95 i 333 Hz 760 µSec
MKS DS 760 333 Hz 760 µSec
MKS 8910A 333 Hz 760 µSec
Robbe FS 61 BB 333 Hz 1.500 µSec
Savox SB-2272 MG 333 Hz 1.500 µSec
Savox SB-2271 MG 333 Hz 1.500 µSec
Savox SC-1257 TG 333 Hz 1.500 µSec
Savox SH-1290 MG 333 Hz 1.500 µSec
Sky HDS-577 200 Hz 1.500 µSec
Sky HDS-877 200 Hz 1.500 µSec
Torq BL 9188 HV 333 Hz 760 µSec
Torq BL 9088 333 Hz 760 µSec
Note: if your type of servo is not in this list, please look up
the parameters in the manual of the servo or on the inter-
net.
Fail Safe
☝ Attention VBar Control’s pre-programmed Fail Safe-Set-
tings will set the servos to hold and the ESC/trottle servo to
the known motor off-position, both if the connection between
satellite and VBar is interrupted and if the radio connection is
interrupted or broken. This way, the energy is taken out of the
system as much as possible, and the model is left on a hope-
fully predictable trajectory.
☝ Attention If the connection can be re-established, (e.g. af-
ter temporary radio interference), you regain control imme-
diately. On an electric heli, the motor will spool up quickly,
the same as from bail out/idle. A combustion engine will not
regain power. Land/autorotate the model immediately and
nd/remedy the cause before ying again.
☝ Attention In case the connection to the model or VBar
breaks, VBar Control will notify
Connection broken
and ad-
vise to turn off the motor switch. Turn off the motor at your
own discretion: we recommed turning off the motor before
the model hits the ground, to avoid further damage.
⚠ Warning Always set the motor switch to ‘Motor Off’ position
when approaching a crashed model: in case the connec-
tion can be re-established, the motor will otherwise spool
up again.
To Next Page
Loading...
Need help?
General
