Mitsubishi Electric R60AD8-G - Page 201

APPX
Appendix 3 Buffer Memory Areas
199
A
• For the R60AD16-G
When the following operations are performed, the data to be used is stored (saved).
• Writing the initial setting by engineering tool
• Turning off and on 'Operating condition setting request' (Y9) (Data is not saved when the mode is switched from the normal
mode to the offset/gain setting mode by 'Mode switching setting' (Un\G296, Un\G297).)
• Writing an offset/gain value in the offset/gain setting mode (When 'User range write request' (YA) is turned off and on)
When restoring the offset/gain setting value in user range setting, set the same data as the saved data in this area to the
corresponding area of the A/D converter module that is the restoration destination.
For the offset/gain setting, refer to the following.
 MELSEC iQ-R Channel Isolated Analog-Digital Converter Module User's Manual (Startup)
■Default value
The default value is 0 for all channels.
Buffer memory name Address
CH Factory default setting offset value (L) CH1 CH2 CH3 CH4 CH5 CH6 CH7 CH8
4004 4008 4012 4016 4020 4024 4028 4032
CH9 CH10 CH11 CH12 CH13 CH14 CH15 CH16
4036 4040 4044 4048 4052 4056 4060 4064
CH Factory default setting offset value (H) CH1 CH2 CH3 CH4 CH5 CH6 CH7 CH8
4005 4009 4013 4017 4021 4025 4029 4033
CH9 CH10 CH11 CH12 CH13 CH14 CH15 CH16
4037 4041 4045 4049 4053 4057 4061 4065
CH Factory default setting gain value (L) CH1 CH2 CH3 CH4 CH5 CH6 CH7 CH8
4006 4010 4014 4018 4022 4026 4030 4034
CH9 CH10 CH11 CH12 CH13 CH14 CH15 CH16
4038 4042 4046 4050 4054 4058 4062 4066
CH Factory default setting gain value (H) CH1 CH2 CH3 CH4 CH5 CH6 CH7 CH8
4007 4011 4015 4019 4023 4027 4031 4035
CH9 CH10 CH11 CH12 CH13 CH14 CH15 CH16
4039 4043 4047 4051 4055 4059 4063 4067
CH User range setting offset value (L) CH1 CH2 CH3 CH4 CH5 CH6 CH7 CH8
4068 4072 4076 4080 4084 4088 4092 4096
CH9 CH10 CH11 CH12 CH13 CH14 CH15 CH16
4100 4104 4108 4112 4116 4120 4124 4128
CH User range setting offset value (H) CH1 CH2 CH3 CH4 CH5 CH6 CH7 CH8
4069 4073 4077 4081 4085 4089 4093 4097
CH9 CH10 CH11 CH12 CH13 CH14 CH15 CH16
4101 4105 4109 4113 4117 4121 4125 4129
CH User range setting gain value (L) CH1 CH2 CH3 CH4 CH5 CH6 CH7 CH8
4070 4074 4078 4082 4086 4090 4094 4098
CH9 CH10 CH11 CH12 CH13 CH14 CH15 CH16
4102 4106 4110 4114 4118 4122 4126 4130
CH User range setting gain value (H) CH1 CH2 CH3 CH4 CH5 CH6 CH7 CH8
4071 4075 4079 4083 4087 4091 4095 4099
CH9 CH10 CH11 CH12 CH13 CH14 CH15 CH16
4103 4107 4111 4115 4119 4123 4127 4131