EasyManuals Logo

NAPCO iSecure User Manual

NAPCO iSecure
80 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #38 background imageLoading...
Page #38 background image
38 All technical manuals are available in PDF format at tech.napcosecurity.com Napco iSecure Security System
Hub by unplugging the AC transformer.
2. Separate the Go-Anywhere Hub housing. With a flat
head screwdriver, push in the two tabs at the bottom to
unhook, then carefully separate the two parts of the Hub
housing (separating the housing disconnects the battery).
3. Remove the six (6) screws that secure the Go-
Anywhere Hub motherboard PCB to the front housing.
See the arrows in Fig. 2 for screw locations.
4. The Antenna Board has "peel and stick" adhesive.
Peel off the protective paper without touching the adhe-
sive.
5. Carefully lift the motherboard only until you have
enough clearance for the following:
With the top edge of the Antenna Board facing
up, secure the antenna adhesive to the interior plas-
tic, as shown in Fig. 3.
Be careful not to lift the motherboard too far, ensuring all
connections remain secure.
Note: Be aware the Top Antenna may become discon-
nected; its connectors can easily be re-inserted after the
next step.
6. Lower the motherboard, re-aligning all mounting holes.
Gently pull the Antenna Board plug and wire toward the
front of the motherboard (this will assist with its connec-
tion to the ISEC-WIFI module in a future step).
If the Top Antenna disconnects from the motherboard,
be sure to carefully re-insert the connections.
7. Replace the six (6) screws that secure the Go-
Anywhere Hub motherboard PCB to the front housing.
See the arrows in Fig. 2 for screw locations.
8. With the ISEC-WIFI PC board in hand, connect the
small Antenna Board plug to the ISEC-WIFI module
socket (see Fig. 4).
The antenna wire should freely rotate while remaining
connected. Important: Handle this wire with care; do
not twist, create sharp bends or apply excessive force.
The ISEC-WIFI allows your
Napco iSecure Go-Anywhere
Hub to connect to the Inter-
net by means of a wireless
(Wi-Fi) link, eliminating a
wired Ethernet cable connec-
tion. Note: The ISEC-WIFI
requires 46mA (standby cur-
rent); refer to the "STANDBY
- BATTERY CALCULATION
WORKSHEET" in this manu-
al to verify that sufficient
power is available.
Prior to opening the
ISEC-WIFI PC board
package or touching
anything inside the
iSecure Go-Anywhere Smart
Hub enclosure, discharge any static electricity from your body
or clothing. Use a grounded wrist strap or touch an unpainted,
grounded metal object.
I N S T A LL A T I O N S T E PS
The Antenna Board (see Fig. 1) has "peel and stick" adhe-
sive that secures it to the inside of the Go-Anywhere Hub
front housing, with its top edge facing up). Keep the wire
away from the "Top Antenna" at the top of the Hub.
1. Remove AC power from the Go-Anywhere Smart
14. Install the ISEC-WIFI
Fig. 2: Arrows show six (6) screws securing the motherboard.
The Top Antenna, is also shown
Top
Antenna
Fig. 3: Carefully lift the motherboard. Note the location of the
Antenna Board's "top edge" (arrow) .
"Top Antenna"
Fig. 1: ISEC-WIFI and Antenna
Board (with adhesive).
Arrow points to top edge.
"Antenna
Board"
ISEC-WIFI

Table of Contents

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the NAPCO iSecure and is the answer not in the manual?

NAPCO iSecure Specifications

General IconGeneral
BrandNAPCO
ModeliSecure
CategorySecurity System
LanguageEnglish

Related product manuals