NEC SL1000 - Call Failure Handling; Camp On and Callback Features; Message Waiting Indicator

LIST OF FIGURES
Figure 1-1 System Configuration....................................................................................... 1-1
Figure 1-2 System Image................................................................................................. 1-12
Figure 1-3 Maximum KSU Capacity - Expandability of Trunk and Extension
(without PRI)............................................................................................. 1-13
Figure 1-4 Maximum KSU Capacity - Expandability of Trunk and Extension (with
PRI)........................................................................................................... 1-14
Figure 2-1 CPU Card Location........................................................................................... 2-3
Figure 2-2 Dimension of the Main and Expansion KSU..................................................... 2-4
Figure 2-3 Vertical Arrangement of KSUs.......................................................................... 2-5
Figure 2-4 Horizontal Arrangement of KSUs..................................................................... 2-6
Figure 2-5 Wall-Mounting Template................................................................................... 2-6
Figure 2-6 Screw Positions................................................................................................ 2-7
Figure 2-7 Sub-Cover Slide-out......................................................................................... 2-7
Figure 2-8 Removing the Sub-Cover................................................................................. 2-8
Figure 2-9 Sub-Cover Open Position................................................................................. 2-8
Figure 2-10 Mounting the KSU.......................................................................................... 2-8
Figure 2-11 Connectors of EXIFB-C1................................................................................ 2-9
Figure 2-12 Removing the Sub-Cover ............................................................................ 2-10
Figure 2-13 Removing the Main-Cover ........................................................................... 2-10
Figure 2-14 EXIFB-C1 PCB Installation........................................................................... 2-11
Figure 2-15 Removing the Plastic Knockouts.................................................................. 2-11
Figure 2-16 Replacing the Main-Cover............................................................................ 2-11
Figure 2-17 Connection of KSUs..................................................................................... 2-12
Figure 2-18 ETH Lug....................................................................................................... 2-13
Figure 2-19 AC Power Cord............................................................................................. 2-14
Figure 2-20 Sub-Cover Open and Hold........................................................................... 2-15
Figure 2-21 Trunk Cabling............................................................................................... 2-16
Figure 2-22 Extension Cabling......................................................................................... 2-17
Figure 2-23 PF/KT Switch of 408M-A1............................................................................ 2-18
Figure 2-24 Cabling......................................................................................................... 2-19
Figure 2-25 Sub-Cover.................................................................................................... 2-19
Figure 2-26 Dimension of the IP4WW-Battery Box.......................................................... 2-21
Figure 2-27 Removing the Front Cover .......................................................................... 2-22
Figure 2-28 Disconnect Battery Connection Cable.......................................................... 2-22
Figure 2-29 Batt Stopper.................................................................................................. 2-23
Figure 2-30 Pulling out the Battery Tray ......................................................................... 2-23
Figure 2-31 Remove the Battery Tray Bracket ............................................................... 2-24
Figure 2-32 Battery Installation........................................................................................ 2-24
Figure 2-33 Connecting the Battery Cables..................................................................... 2-25
Figure 2-34 Installation of Battery Tray Cover................................................................. 2-25
Figure 2-35 Inserting the Battery Tray............................................................................. 2-26
Figure 2-36 Secure Batt Stopper Bracket........................................................................ 2-26
Figure 2-37 Connecting the Battery Connection Cable................................................... 2-27
Figure 2-38 Installation of Front Cover............................................................................ 2-27
Figure 2-39 Bases and Support of the Battery Box......................................................... 2-28
Figure 2-40 Floor-Mount Spacing Guide.......................................................................... 2-28
Figure 2-41 Mounting the Battery Box............................................................................. 2-29
Figure 2-42 Securing the Battery Box.............................................................................. 2-29
Figure 2-43 Assemble Battery Box Base......................................................................... 2-30
Figure 2-44 Wall-Mount Spacing Guide........................................................................... 2-31
Figure 2-45 Removing the Front Cover .......................................................................... 2-32
SL1000
ISSUE 3.0
vi Hardware Manual