Optex Virtual Loop - 10 Specifications; Detection Area Diagram

-37-
Specifications
10
10-2
Detection Area Diagram
10-1
Specifications
Top view Side view
Installation height 0.5m(20’’ ), Sensitivity: 4, Detection area check mode
* Under normal operation, the detection area by an actual vehicle may be smaller.
0
1
1
1 2 3 4 5 60 7
3m
1m
8m setting
8 9
0
1
2
3
1 2 3 4 5 60 7 8 9
1m 3m 8m setting
[Unit: m (1m ≈ 3.3ft.)]
<Notice>
Please note that we are not responsible for any damage that occurred when the equipment is operated or installed improperly.
Specifications are subject to change without notice for improvement.
Vehicle Detection Sensor (Surface mount）
OVS-02GT
Microwave ( FMCW)
Microwave
︓
24GHz
、
BLE communication
︓
2.4GH
ｚ
MIN 500ms
12 to 24VAC/DC
Heater enabled︓Up to 300mA、Heater disabled︓Up to 90mA( at 24V )
1 Non-voltage solid state relay output 30VDC 0.3A or less (resistance load) (N.O. / N.C.)
2
Non-voltage mechanical relay output 30VDC 1A or less (resistance load) (N.O. / N.C.)
Off / 0.5 / 1 / 2 / 3 / 4
Off / 0.5 / 1 / 2 / 3 / 10 / 30 / 60
Detection / Pre-detection / Mask
Holding / Pulse IN / Pulse OUT
150ms / 250ms / 500ms / 1s
N.O. contact Non-voltage relay Input
On resistance 100Ω or less, Off resistance 200kΩ or more,
Internal pull-up voltage: approx. 3.3V
Link(OR gate) / Link (AND gate) / Inhibit / Wake
Barrier-Activation,Protection / Slide gater-Activation,Protection /
Swing gater-Activation,Protection, Shadow
2 to 35km/h (1.2 to 22 mi/h)
1.5m(7ft.) to 8.0m(26ft.) *0.5m(20in.) pitch
Level 1 to 7
Level 1 to 7
Level 1 to 7
Off / 2.5 / 5 / 10 / 30 / 60 / 120
Off / Low / Middle / High
Off / Low / Middle / High
Off / 0.5 / 1 / 2 / 3 / 4 / 5 / 10 / 20 / 40
Level 1 to 4
5 / 15
/ 60 / 180 / Infinity
O
ｆｆ
/ On
Switchable (with the smartphone App or by holding a magnet close to the unit)
Detection operation
Standby : Solid green, Detected : Solid red, Bad environment : Solid purple,
Calibration uncompleted : Solid blue
Wake up Wake up : Solid blue for 3 seconds
Sensor reset Completed reset : Blinking blue (Fast) for 2 seconds
Setting
Detection operation
Stanby : Blinking green(slow), Detected : Blinking yellow(slow),
Bad environment : Blinking purple(slow), Calibration uncompleted : Blinking blue(slow)
Area check
Stanby : Blinking green(slow), Pre-detected : Blinking yellow(slow),
Detected : Blinking red(slow)
Calibration
In process : Blinking Blue & Green, Error Unstable : Blinking Red & Yellow(Fast),
Error High reflection : Blinking Red & Blue(Fast), High reflection : Blinking Purple(for 10s)
-30 to 50℃ (-22 to 122 °F)
95％ max. ( no condensation )
IP66 / NEMA4
Indoor / Outdoor
500mm(20in.) ( from the ground to the bottom of the unit)
Left and right︓±96°(3°pitch )
600g (21oz) ( Including accessories)
4pcs attached screws (2pcs Metric coarse thread M4x12, 2pcs Tapping screw 4x20),
Quick reference guide
Smartphone
app
connection
mode
Slide gate cancellation
Accessories
Installation Location
Indicator
Application
Device
setting
Sensor Angle Adjustment
Weight
Detection range
Installation Height
Ambient Temperature
Operating Ambient Humidity
Degree of Protection
On / Off
Standard
operation
mode
Supply voltage
Power consumption
Response
Name
Model
Detection method
Frequency
Fine tuning presence
Close range sensitivity
Sensitvity boost timer [s]
Presence detection timer [min]
Side approach detection [s]
Vibration sensitivity
Sensitvity boost
Relay Response time
Main sensitivity
Detectable vehicle speed
Input
Spec
Mode
Spec
Output
Delay [s]
Hold timer [s]
Mode
Type
Pulse time duration