What does E03 error mean on Owandy Medical Equipment, and how can I resolve it?
If your Owandy Medical Equipment displays error E03, which indicates that more than one key was pressed at start-up, first verify that no buttons are actually pressed. Then, switch the system off and on again. If the error continues, replace the CPU board.
What does CH0 error mean on Owandy Medical Equipment?
If the Owandy Medical Equipment displays error CH0, which indicates a memory checksum error (EEPROM), follow the displayed procedure if it occurs at the first start-up after replacing the EEPROM. If it occurs during normal operation, replace the EEPROM; if that's not sufficient, replace the CPU board.
Explains symbols used in the manual for notes and warnings.
Provides contact information for technical queries.
General warnings and important safety precautions for operating the Ow-RX unit.
Details compliance with EMC standards for electromagnetic emissions.
Outlines EMC immunity standards and requirements for the operating environment.
Provides recommended distances for mobile and portable radio equipment.
Describes safety measures and precautions related to X-ray exposure.
Information on material disposal and environmental considerations at end-of-life.
Explains various symbols used in the manual and on the device.
Details the identification plates found on the device components.
Overview of the Ow-RX unit's capabilities, models, and versions.
Describes the technical specifications of the HF generator.
Details the components and functionality of the extension and scissors arms.
Technical specifications of the tube-head component.
Description of the timer unit, its display, and controls.
Outlines different system configurations available for the Ow-RX.
Describes the standard setup of the Ow-RX system.
Details the setup for the remote timer configuration.
Explains the mobile stand configuration of the Ow-RX.
Describes the setup for the remote X-ray button.
Details the setup for the wireless X-ray button configuration.
Explains methods for measuring technical factors like kVp and exposure time.
Presents characteristic curves for the X-ray tube.
Lists the standards and directives the Ow-RX complies with.
Provides dimensional drawings and specifications for the device.
Details various mounting methods and safety considerations for wall installation.
Covers electrical requirements and pre-installation settings for power connection.
Step-by-step guide for installing the Ow-RX unit on a wall.
Instructions for setting up the timer in the standard wall configuration.
Guide for assembling the mobile stand and installing the timer.
Instructions for assembling the various arm components.
Steps to assemble the extension arm component.
Instructions for assembling the scissors arm (DP arm).
Guide to assembling the stand arms set.
Details on installing optional components.
How to connect external signaling devices to the unit.
Instructions for installing the remote X-ray button.
Procedures related to the wireless X-ray button.
Procedure for inserting batteries into the wireless X-ray button.
Steps for assembling the wireless upgrade kit.
Procedure for pairing the wireless X-ray button with the timer.
Configuration steps for the remote timer.
Instructions for setting up the wall support for the remote timer.
Steps for setting up the remote timer unit.
Recommendation for using chemical screws on hollow bricks.
Guidance on electrical connections for the unit.
Guide for electrical connections in standard and mobile stand setups.
Electrical connection steps for the remote timer version.
Specific electrical connection steps for the remote timer wall support.
Details on connecting the remote timer unit.
Describes the sequence of checks performed when the system starts up.
Explains when and how to adjust the arms for ergonomic use.
Procedure for adjusting the friction on the extension arm support.
Steps to adjust the friction on the extension arm.
Guide for adjusting the friction and spring balance of the scissors arm.
Configuration for system stand-by timeout duration.
Setting for the duty cycle, affecting cool down time.
Functionality to view and reset the exposure counter.
Parameter to adapt exposure times based on film speed.
Setting for using a 30cm limiter cone, adjusting exposure times.
Adjustment for display back light intensity.
Selection of the user interface language.
Adjustment for LCD display contrast.
Setting to define the X-ray tube type (e.g., Toshiba, CEI).
Procedure to reset system configuration to factory defaults.
Explains error messages, their meanings, causes, and corrective actions.
Details fatal errors occurring during startup or idle states.
Lists fatal errors that interrupt X-ray emission.
Describes non-fatal, resettable errors and their solutions.
Instructions for replacing the tubehead and driver board as a unit.
Step-by-step guide for replacing the tubehead component.
Procedure for replacing the driver board.
Instructions for replacing the CPU board.
Guide for replacing the device keypad or membrane.
Procedures for replacing the scissors arm.
Steps to replace the scissors arm in the standard wall configuration.
Procedure for replacing the scissors arm on a mobile stand.
General| Brand | Owandy |
|---|---|
| Model | RX |
| Category | Medical Equipment |
| Language | English |
To Next Page