Panasonic AAD03011 - Parameter Setting Table

䃂
Parameter Setting
䊶㩷For details on the data type in the table, refer to "Display data and transmission data"
on page 80.
Parameter
No.
Register
No.
Function name
Displayed
Data
Unit
Internal
Data
Data
type
P01 DT1 1ST acceleration time sec 09990 2
P02 DT2 1ST deceleration time sec 09990
0࡮1࡮2
2
4
P03 DT3 V/F pattern


P04 DT4 V/F curve 0࡮10࡮1
P05 DT5 Torque boost level 0㨪40 % 040 1
1
P06 DT6 Electronic thermal function select 0࡮1࡮2࡮3  031
P07 DT7 Setting of thermal current 0.1㨪100 A 11000 2
P08 DT8 Operation command select 0㨪3  031
P09 DT9 Frequency setting signal 0㨪6 

061
1
P10 DT10 Stop mode 0࡮10࡮1
P11 DT11 Stop frequency 0.5㨪60 Hz
Hz
Hz
Hz
Hz
Hz
Hz
506000 3
P12 DT12 DC brake time 0࡮0.1㨪120 sec 01200 2
P13 DT13 DC brake level 0㨪100 

020 5
P14 DT14
Max. output frequency
50㨪250 500025000 3
P15 DT15 Base frequency 45㨪250 450025000 3
P16 DT16 Overcurrent stall prevention function 0࡮10࡮1
P17 DT17 Overvoltage stall prevention function 0࡮10࡮1
P18 DT18 Skip frequency 1 0࡮0.5㨪250
0࡮0.5㨪250
0࡮0.5㨪250
025000 3
P19 DT19 Skip frequency 2 025000 3
P20 DT20 Skip frequency 3 025000 3
P21 DT21 Skip frequency band width 0㨪10 010 1
1
1


1

1

1

1
P22 DT22 Current limit function 0࡮0.1㨪9.9 sec 099 2
P23 DT23 Start mode 0࡮1࡮2࡮3
0࡮1࡮2࡮30࡮1࡮2࡮3
0࡮1࡮2࡮3
P24 DT24 Ride-through restart 0࡮1࡮20࡮1࡮2
P25 DT25 Wait time 0.1㨪100 sec 1-1000 2
P26 DT26 Retry function select
P27 DT27 Retry times 1㨪10 󱂖 110 1
P28
DT28
Lower frequency clamp
0.5㨪250 Hz 5025000 3
P29 DT29 Upper frequency clamp 0.5㨪250 Hz 5025000 3
P30 DT30 Monitor select 0࡮1
0࡮1
P31 DT31 Line speed multiplier 0.1㨪100  11000 2
P32 DT32 Max. output voltage 0࡮1㨪500 V 0-500 1
P33 DT33 OCS level 1㨪200 % 1200 1
P34 DT34 Carrier frequency 0.8㨪15.0 kHz 086
84
0࡮0.1㨪999
0࡮0.1㨪999
50࡮60࡮FF