Pentair Sta-rite INTELLIPRO User Manual

17
INTELLIPRO
®
Variable Speed Pump Installation and User’s GuideINTELLIPRO
®
Variable Speed Pump Installation and User’s Guide
CONNECTING TO AN AUTOMATION SYSTEM
External Control with IntelliComm
®
Communication Center
Use the RS-485 communications cable to remotely
control the pump from an IntelliComm communication
center.TheIntelliCommsystemprovidesfour(4)pairs
of input terminal connections. These inputs are actuated
byeither15-240VACor15-100VDC.Usethedevice
inputs, to control the programmed pump speeds.
Note:FortheIntelliPro
®
Variable Speed Pump to accept
commands from the IntelliComm system, the pump
mustbeinthe“RunningSchedules”mode(LEDabove
Start/Stopbuttonison).Ifmorethanoneinputisactive,
the highest number will be communicated to the pump.
The IntelliComm system will always communicate to
pumpusingADDRESS#1.
Refer back to page 12 for instructions for setting up
Programs in the External Control menu.
External Control is for programming speeds that will
run when the IntelliComm communication center
controller sends it a command.
Forexample,Terminal3and4inIntelliCommsystem
willcorrespondtoExternalControlProgram#1.(5
and6toExtCtrl#2).UsetheExternalControlfeature
to program the IntelliComm communication center.
Terminal
Number
Terminal
Name
Voltage
Max.
Current
Phase
Type
Frequency
1-2
Power
Supply
100-240
VAC
100mA 1Input 50/60Hz
3-4
Program
1
15-240
VAC
or
15-100
VDC
1mA 1Input
50/60Hz
5-6
Program
2
15-240
VAC
or
15-100
VDC
1mA 1Input 50/60Hz
7-8 Program
3
15-240
VAC
or
15-100
VDC
1mA
1Input 50/60Hz
9-10
Program
4
15-240
VAC
or
15-100
VDC
1mA 1Input
50/60Hz
11
12
RS-485
+Data:
Yellow
-Data:
Green
-5to+5
VDC
5mA
1
Output N/A
Ground
IntelliComm Communication Center
Program Number Priority
Ifprograms1 and 2 are activated,program2 will
run,regardlessoftheassignedspeed(RPM).The
higherprogramnumberwillalwaystakepriority.
Connecting to EasyTouch
®
and
IntelliTouch
®
Control Systems
The pump can be controlled by an EasyTouch or
IntelliTouchsystemviatheRS-485communication
cable.TheEasyTouchand/orIntelliTouchcontrol
system starts, stops and controls the speed of the pump.
EasyTouch and/or IntelliTouch systems rewrite the
pumpmemorywhenacommandisgiven.Thiscantake
several seconds and can cause a delay until the pump
physically responds.
The pump control panel is disabled when communicating
with an EasyTouch and/or IntelliTouch system. The
EasyTouch and/or IntelliTouch system will not start
communicating with the pump until the pump is
assigned to a circuit. Thedefaultpumpaddressis“1”
(onlyaddressforEasyTouchsystem).
Wiring Terminal Descriptions for IntelliComm
Communication Center
See page 8 for details about how to check and or set
the pump address. For more information, refer to the
IntelliTouch (P/N 520100) or EasyTouch Automation
System User’s Guide (P/N 520584).
Installation and User’s Guides are available at:
www.pentairpool.com/pool-owner/manuals.

Pentair Sta-rite INTELLIPRO Specifications

General

Brand	Pentair
Model	Sta-rite INTELLIPRO
Category	Water Pump
Language	English