64
Table of Error Code (Digital adjustment)
When adjustment error is occurred, below screen will be displayed.
[Table of Error Code for Digital adjustment]
AA - BB - CC - DD - EE
AA：
00 Initialize
02 CCD Information
04 Pre-Process Gain
05 ISO Base Gain
06 Bad Pixel Defection
BB-CC： Initialize (AA=00) BB-CC： ISO Gain (AA=05) DD-EE：
01-01 Reading setting file 01-01 Mode dial is not switched 01-00
02-01 Camera - PC connection 01-02 01-01
02-02 Camera - PC connection 01-03 01-02
02-03 Acquisition of camera status 01-04 02-01 Can not access to file
02-04 Acquisition of camera information 01-05 Mode dial is not "M" mode 05-01
03-01 CCD file open 01-07 Not setting multi segment metering 06-01
03-02 CCD file size not correct 01-09 Not setting to allowing to release at M position 07-00
03-04 CCD file data is not correct 01-10 SR SW is not set to OFF 07-01
05-05 Missing setting file, light calibration file 03-01 Can not set shutter speed 08-00 Out of range (too low )
06-01 DSP version is not the same 03-02 Can not set diaphragm 08-01 Out of range (too high)
06-02 CPU version is not the same 03-03 Can not set ISO 08-02 White scratch: many of high level pixels
07-01 Can not read ISOgain adjustment 03-04 Can not set exposure compensation 08-03 White scratch: cannot correct (continuity scratch)
07-02 Can not read PPG adjustment value 03-05 Can not set WB 08-04 Black scratch: cannot correct (continuity scratch)
03-06 Can not metering 08-05 Cannot correct scratch
BB-CC： Pre-Process Gain (AA=04) 03-07 Can not acquisition of AE information 08-06 HW scratch correct failure
01-01 Mode dial is not switched 04-01 08-07 Can not set power control
01-02 10-01 08-08 AFE calibration NG
01-03 04-02 08-09 Can not acquisition of power control value
01-04 10-02 08-10 light compensation RGG ratio
01-05 Mode dial is not "M" mode 08-01 09-00 FE version is not correct
01-07 Not setting multi segment metering 14-01 09-01 Skipped previous process
01-09 Not setting to allowing to release at M position 17-01 Can not set adjusted value 09-02 Trying to adjust master body
01-10 SR SW is not set to OFF 17-02 Not switch to writing mode for adjusted value
03-01 Can not set shutter speed 17-03 Can not write adjusted value
03-02 Can not set diaphragm
03-03 Can not set ISO BB-CC： Bad Pixel Defection (AA=06)
03-04 Can not set exposure compensation 01-01 Mode dial is not switched
03-05 Can not set WB 01-02
03-06 Can not metering 01-03
03-07 Can not acquisition of AE information 01-04
05-01 01-05 Mode dial is not "M" mode
08-01 01-07 Not setting multi segment metering
14-01 01-09 Not setting to allowing to release at M position
05-02 01-10 SR SW is not set to OFF
08-02 02-02 Can not set dummy lens
14-02 03-01 Can not set shutter speed
07-01 03-02 Can not set diaphragm
12-01 03-03 Can not set ISO
20-01 Can not set adjusted value 03-04 Can not set exposure compensation
20-02 Not switch to writing mode for adjusted value 03-05 Can not set WB
20-03 Can not write adjusted value 03-06 Can not metering
03-07 Can not acquisition of AE information
08-08 Can not write adjusted value
BB-CC： Error item
Can not setting camera
Can not set PPG gain value
Can not set CCD gain value
Can not set CCD gain value
CCD output value is not correct
Connection error for USB or No power of Camera
Can not transfer USB command correctly
CCD output value is not correct
DD-EE： Error content
AA： Adjusting item
Can not setting camera
Can not set PPG gain value
Can not setting camera
Initialize check
CCD data display
WB Adjustment
ISO Gain adjustment
CCD pixel compensation adjustment
To Next Page
Loading...
