Pleiger Elektronik
GmbH & Co. KG
Page: 48 Manual for 362MC Edition: 6/2007 Subject to modifications
Parameter Value (min Meaning Comment
1
st
controller max)
1SpTypA1SpTypA
1SpTypA1SpTypA
1SpTypA
fixedfixed
fixedfixed
fixed Setpoint type A = fixed value Extension for selection of Setpoint
extern extern
extern extern
extern = external input programme in addition to types fixed
StpPrg1StpPrg1
StpPrg1StpPrg1
StpPrg1 = setpoint and external
StpPrg2StpPrg2
StpPrg2StpPrg2
StpPrg2 programme The programme no. 1 to 5 to be
StpPrg3StpPrg3
StpPrg3StpPrg3
StpPrg3 programme no. 1 executed is selected directly here.
StpPrg4StpPrg4
StpPrg4StpPrg4
StpPrg4 to programme no. 5 The fixed-value entry 1SetpA is
StpPrg5StpPrg5
StpPrg5StpPrg5
StpPrg5 omitted when SetpPrg is selected.
1SpTypB1SpTypB
1SpTypB1SpTypB
1SpTypB
fixedfixed
fixedfixed
fixed Setpoint type B = fixed value As in the case of 1SpTypA, a
extern extern
extern extern
extern = external input a setpoint programme can also be
StpPrg1StpPrg1
StpPrg1StpPrg1
StpPrg1 = setpoint assigned for the second setpoint B,
programme no. 1 if the changeover function is active.
StpPrg5StpPrg5
StpPrg5StpPrg5
StpPrg5 to programme no. 5 See Setpoint menu, 5.3
1T-Lowp1T-Lowp
1T-Lowp1T-Lowp
1T-Lowp Filter time for setpoint changeover
1Alarm-1Alarm-
1Alarm-1Alarm-
1Alarm- See 5.3 lower alarm limit See Setpoint menu, 5.3
1Alarm+1Alarm+
1Alarm+1Alarm+
1Alarm+ upper alarm limit
Parameter The following parameters for the 2
nd
controller are only displayed when
2
nd
controller 2 controllers have been selected in the Profile menu.
2SpTypA2SpTypA
2SpTypA2SpTypA
2SpTypA
fixedfixed
fixedfixed
fixed Setpoint type A = fixed value As for the 1
st
controller, a setpoint
extern extern
extern extern
extern = external input programme can also be assigned to
StpPrg1StpPrg1
StpPrg1StpPrg1
StpPrg1 = setpoint to the 2
nd
controller.
programme no. 1 See 1SpTypA (above)
StpPrg5StpPrg5
StpPrg5StpPrg5
StpPrg5 to programme no. 5
2SpTypB2SpTypB
2SpTypB2SpTypB
2SpTypB
fixedfixed
fixedfixed
fixed Setpoint type B = fixed value
extern extern
extern extern
extern = external input
StpPrg1StpPrg1
StpPrg1StpPrg1
StpPrg1 = setpoint See 1SpTypB (above)
programme no. 1
StpPrg5StpPrg5
StpPrg5StpPrg5
StpPrg5 to programme no. 5
2T-Lowp2T-Lowp
2T-Lowp2T-Lowp
2T-Lowp Filter time for setpoint changeover
2Alarm-2Alarm-
2Alarm-2Alarm-
2Alarm- See 5.3 lower alarm limit See Setpoint menu, 5.3
2Alarm+2Alarm+
2Alarm+2Alarm+
2Alarm+ upper alarm limit
*
SpPrgNoSpPrgNo
SpPrgNoSpPrgNo
SpPrgNo
1 1
1 1
1 Programme selection for entry The selected setpoint programme is
5 5
5 5
5 Programme no. 1 to 5 is loaded in the Entry field.
Setp1 Setp1
Setp1 Setp1
Setp1
0.0°C 0.0°C
0.0°C 0.0°C
0.0°C 1
st
step Entries for the 20 steps of the loaded
200.0°C200.0°C
200.0°C200.0°C
200.0°C Setp1 - temperature per example setpoint programme.
Time1 Time1
Time1 Time1
Time1
-5s -5s
-5s -5s
-5s Time1 - 1-9999s; (time 0 or negative Setpoint here e.g. 0-200°C; see also
9999s 9999s
9999s 9999s
9999s see Programme functions) Explanatory note on setpoints
Setp2 Setp2
Setp2 Setp2
Setp2 See above 2
nd
step (5.3.1)
Time2 Time2
Time2 Time2
Time2
to See also Programme structure,
Setp20 Setp20
Setp20 Setp20
Setp20 See above 20
th
step Programme entry and
Time20 Time20
Time20 Time20
Time20 (last step) Programme
functions
* If a setpoint programme is selected via “SpPrgNo” in order to carry out changes to the
programming of the steps and if this programme has been activated under 1SpTypA, 1SpTypB,
2SpTypA or 2SpTypB, the changes should be carried out in manual mode only.
Parameterisation
The setpoint programme is activated and entries effected in the extended Setpoint menu:
To Next Page
Loading...
Need help?
General