A
ashley20Sep 6, 2025
How to exit Hex Dump Mode on Ricoh Aficio SP C320DN Printer?
- YywilliamsSep 6, 2025
If your Ricoh Printer is in Hex Dump Mode, turn off the printer after printing, and then turn it back on.
To Next PageTo Next PageHow to exit Hex Dump Mode on Ricoh Aficio SP C320DN Printer?
If your Ricoh Printer is in Hex Dump Mode, turn off the printer after printing, and then turn it back on.
How to fix color shift on Ricoh Aficio SP C320DN?
If a color shift occurs with your Ricoh Printer, and the colors are not as you require them, perform [Color Registration].
How to fix 'Ethernet Board Error' on Ricoh Aficio SP C320DN?
If the Ricoh Printer displays 'Ethernet Board Error', pull out and then re-install the controller board. If the problem persists, contact your sales or service representative.
What to do if my Ricoh Printer says 'Job Suspended'?
If the Ricoh Printer displays 'Job Suspended', turn the printer off, and then turn it on again to recover.
How to fix 'Classification Code Error' on Ricoh Aficio SP C320DN?
If the Ricoh Printer displays a 'Classification Code Error', it means a classification code is not specified for the print job. Enter a classification code using the printer properties and print the document again.
What does 'USB has a problem' mean on my Ricoh Aficio SP C320DN Printer?
If your Ricoh Printer displays 'USB has a problem', it means the printer has detected a USB board failure. Turn the power off, and then on again. If the problem persists, contact your sales or service representative.
How to turn off Energy Saver Mode on Ricoh Aficio SP C320DN Printer?
If your Ricoh Printer is in Energy Saver Mode, press any key to return to the normal mode.
What to do if my Ricoh Aficio SP C320DN Printer says 'Cover Open. Please close the indicated cover'?
If your Ricoh Printer displays 'Cover Open. Please close the indicated cover,' simply close the cover indicated on the control panel.
Why does my Ricoh Aficio SP C320DN Printer say 'Cannot connect with DHCP server.(101/201)'?
If the Ricoh Printer shows 'Cannot connect with DHCP server.(101/201)', it means the printer cannot obtain an IP address from the DHCP server. It is recommended to consult your network administrator.
How to fix 'Check network settings.(103/203)' error on Ricoh Printer?
If your Ricoh Printer displays 'Check network settings.(103/203)', it indicates that the IP address setting is incorrect. You should check the IP address, subnet mask, and gateway address.
General| Print Technology | Laser |
|---|---|
| Duplex Printing | Yes |
| Processor | 400 MHz |
| Supported Operating Systems | Windows, Mac OS, Linux |
| Resolution | 1200 x 1200 dpi |
| Connectivity | USB 2.0, Ethernet |
| Memory | 128 MB (expandable to 640 MB) |
| Dimensions | 400 x 428 x 368 mm |
| Print Speed | Up to 26 ppm |
| Monthly Duty Cycle | Up to 50, 000 pages |
Explains the procedures for turning the printer's power on and off.
Guides on configuring network settings for the printer's Ethernet interface.
Details how to manually assign an IP address to the printer.
Guides on configuring settings for the printer's Wireless LAN connection.
Explains how to configure security settings for the Wireless LAN.
Provides instructions for replacing the printer's print cartridge.
Details the procedure for replacing the waste toner bottle.
Explains how to replace the intermediate transfer unit.
Guides on how to replace the printer's maintenance kit.
Explains control panel messages and corresponding actions.
Provides troubleshooting steps for when the printer fails to print.
Discusses common causes and solutions for frequent paper misfeeds.
Provides steps for safely removing jammed paper from the printer.
