Roland SP-404MK2 - Ko-Da-Ma; Zan-Zou; To-Gu-Ro

Appendix
116
Ko-Da-Ma
This creates a reverberating audio effect.
Parameter
Value
Explanation
TIME
1/32, 1/16T, 1/32D, 1/16, 1/8T, 1/16D,
1/8, 1/4T, 1/8D, 1/4, 1/2T, 1/4D, 1/2, 1/1T,
1/2D, 1/1
Sets how much the effect sound is delayed.
FEEDBACK
0–99 (%)
Adjusts how much the effect sound is repeated.
SEND
0–100
Adjusts the volume of sound sent to the effect.
L DAMP F
FLAT, 80, 100, 125, 160, 200, 250, 315,
400, 500, 630, 800 (Hz)
Sets the frequency range that is attenuated each time the delay
repeats.
H DAMP F
630, 800, 1000, 1250, 1600, 2000, 2500,
3150, 4000, 5000, 6300, 8000, 10000,
12500, FLAT (Hz)
MODE
SINGLE, PAN
When this is set to “SINGLE”, the effect sound comes from the
center; and when this is set to “PAN”, the effect sound is heard on
the left and the right.
Zan-Zou
For left and right sounds, this effect applies delay to the negative phase of the sound. This gives the lingering effect of a sonic
“afterimage”.
The effect works for stereo sound, and does not have any effect on mono sound.
Parameter
Value
Explanation
TIME
1–100 (when the SYNC parameter is OFF)
1/32, 1/16T, 1/32D, 1/16, 1/8T, 1/16D, 1/8, 1/4T, 1/8D,
1/4, 1/2T, 1/4D, 1/2, 1/1T, 1/2D, 1/1 (when the SYNC
parameter is ON)
Sets the sound delay time.
FEEDBACK
0–99
Adjusts the amount of feedback for the effect.
HF DAMP
200, 250, 315, 400, 500, 630, 800, 1000, 1250, 1600,
2000, 2500, 3150, 4000, 5000, 6300, 8000, OFF (Hz)
Sets the frequency range at which the effect sound
is attenuated (how clearly defined the afterimage
sounds).
LEVEL
0–100
Adjusts the volume of the effect sound.
MODE
2TAP, 3TAP, 4TAP
Sets how the effect sound lingers.
SYNC
OFF, ON
When this is ON, the effect sound synchronizes with
the tempo.
To-Gu-Ro
This gives the sound an undulating effect, based on the image of a coiled-up snake.
Parameter
Value
Explanation
DEPTH
0–100
Adjusts how much the playback speed should be
slowed down.
RATE
0–100 (when the SYNC parameter is OFF)
1/128, 1/64, 1/32, 1/16, 1/8, 1/4, 1/2, 1/1, 2/1 (when
the SYNC parameter is ON)
Sets the period at which the playback speed is
lowered.
RESONANCE
0–100
Adjusts the filter’s resonance level.
Increasing the value further emphasizes the effect,
for a more unusual sound.
FLT MOD
0–100
Attenuates the high-frequency range according to
the playback speed.
AMP MOD
0–100
Attenuates the volume according to the playback
speed.
SYNC
OFF, ON
When this is ON, the effect sound synchronizes with
the tempo.